IBM 9006-12C Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 126

IBM 9006-12C Скачать руководство пользователя страница 108

About this task

CAUTION:

or

or

The weight of this part or unit is between 18 and 32 kg (39.7 and 70.5 lb). It takes two persons to
safely lift this part or unit. (C009)

Procedure

1.

Using two people, one on each side of the system, lift the system from the table.

2.

Align the system rails on each side of the system with the rack rails.

3.

Push the system into the rack until you hear each rail click into place.

4.

Before releasing your hold on the system, ensure that the rails are engaged by sliding the system
forward into service lock position. Check that the rails are properly seated. If the rails are not fully
engaged, the system could drop.

5.

Release the rail safety latches (A) by lifting them upward, as shown in Figure 92, then push the
system fully into the rack. The safety latches work in opposite directions; the latch on one side moves
up while the latch on the other side moves down.

6.

Fasten the two front screws (C) to secure the system to the rack.

7.

Using your labels, reconnect the cables at the rear of the system unit.

8.

If you removed the storage drives, using your labels, replace the drives in their proper locations.

Figure 92. Placing the system into the operating position

92

Power Systems: Servicing the IBM Power System LC921 (9006-12C)

«
...
106
107
108
109
110
...
»

Содержание 9006-12C































































































































Отзывы:

Нет отзывов