manualshive.com logo in svg

IBM 9006-12C, Руководство пользователя, Страница: 117 / 126

Поделиться
Скачать
IBM 9006-12C Скачать руководство пользователя страница 117

European Community contact:
IBM Deutschland GmbH
Technical Regulations, Abteilung M456
IBM-Allee 1, 71139 Ehningen, Germany
Tel: +49 800 225 5426
email: [email protected]

Warning:

This is a Class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

VCCI Statement - Japan

The following is a summary of the VCCI Japanese statement in the box above:

This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a
domestic environment, radio interference may occur, in which case, the user may be required to take
corrective actions.

Japan Electronics and Information Technology Industries Association Statement

This statement explains the Japan JIS C 61000-3-2 product wattage compliance.

This statement explains the Japan Electronics and Information Technology Industries Association (JEITA)
statement for products less than or equal to 20 A per phase.

This statement explains the JEITA statement for products greater than 20 A, single phase.

Notices

101

Содержание 9006-12C































































































































Отзывы:

Нет отзывов