IBM 9006-12C Скачать руководство пользователя страница 106

Страница: 106 / 126

Replace the two cover screws (2) at the rear of the cover.

Service and operating positions for 9006-12C

Learn how to place an IBM Power System LC921 (9006-12C) system into the service or operating position.

Placing an 9006-12C system into the service position

Learn how to place an IBM Power System LC921 (9006-12C) system into the service position.

Before you begin

The systems must be removed from the rails for servicing.

CAUTION:

The weight of this part or unit is between 18 and 32 kg (39.7 and 70.5 lb). It takes two persons to
safely lift this part or unit. (C009)

Notes:

When you slide a system out of a rack, ensure that all stability plates are firmly installed to prevent the
rack from toppling. Slide only one system out at a time.

Figure 90. Replacing and securing the cover

Power Systems: Servicing the IBM Power System LC921 (9006-12C)

Содержание 9006-12C































































































































Результаты поиска

Содержание 9006-12C

Отзывы:

Бренды по названию

Популярные бренды

IBM 9006-12C, Руководство пользователя

Результаты поиска

Содержание 9006-12C

Отзывы:

Бренды по названию

Популярные бренды