manualshive.com logo in svg

IBM 9006-12C, Руководство пользователя

Поделиться
Скачать
IBM 9006-12C Скачать руководство пользователя страница 102

Removing a power supply from the 9006-12C or 9006-22C

Learn how to remove power supplies in the IBM Power System LC921 (9006-12C) or IBM Power System
LC922 (9006-22C) systems.

About this task

If a single power supply failed, it can be replaced while the system is running.

Procedure

1.

Attach the electrostatic discharge (ESD) wrist strap. The ESD wrist strap must be connected to an
unpainted metal surface until the service procedure is completed, and if applicable, until the service
access cover is replaced.
Attention:

v

Attach an electrostatic discharge (ESD) wrist strap to the front ESD jack, to the rear ESD jack, or to
an unpainted metal surface of your hardware to prevent the electrostatic discharge from damaging
your hardware.

v

When you use an ESD wrist strap, follow all electrical safety procedures. An ESD wrist strap is
used for static control. It does not increase or decrease your risk of receiving electric shock when
using or working on electrical equipment.

v

If you do not have an ESD wrist strap, just prior to removing the product from ESD packaging and
installing or replacing hardware, touch an unpainted metal surface of the system for a minimum of
5 seconds. If at any point in this service process you move away from the system, it is important to
again discharge yourself by touching an unpainted metal surface for at least 5 seconds before you
continue with the service process.

2.

Label and remove the power cord from the power supply to remove. For instructions, see
“Disconnecting the power cords from an 9006-12C or 9006-22C system” on page 93.

3.

Remove the power supply from the system.

a.

To unseat the power supply from its position in the system, push the locking-tab to the left as
shown in Figure 87 on page 87.

b.

Grasp the power supply handle with one hand, and pull the power supply partially out of the
system.

c.

Place your other hand underneath the power supply and pull the power supply out of the system
and place it on an ESD mat.

86

Power Systems: Servicing the IBM Power System LC921 (9006-12C)

Содержание 9006-12C































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды