IBM 7220 Скачать руководство пользователя страница 132

Страница: 132 / 155

E-8

Appendix E, ALPHABETICAL LISTING OF COMMANDS

FSTART[.] [n]

Oscillator frequency sweep start frequency

Sets the start frequency for a subsequent sweep of the internal oscillator frequency.

In fixed point mode, n is in millihertz.

In floating point mode n is in hertz.

FSTEP[.] [n

]

Oscillator frequency sweep step size and type

The frequency may be swept either linearly or logarithmically, as specified by
parameter n

. The step size is specified by parameter n

Log sweep n

= 0

In fixed point mode, n

is the step size in thousandths of a percent.

In floating point mode n

is in percent. The range of n

is 0 to 100.00 %

Linear sweep n

= 1

In fixed point mode, n

is the step size in millihertz.

In floating point mode n

is in hertz. The range of n

is 0 to 10 kHz

FSTOP[.] [n]

Oscillator frequency sweep stop frequency

Sets the stop frequency for a subsequent sweep of the internal oscillator frequency.

In fixed point mode, n is in millihertz.

In floating point mode n is in hertz.

GP [n

]]

Set/read GPIB parameters

sets the GPIB address in the range 0 to 31.

sets the GPIB terminator and the test echo function according to the following

table:

Terminator

[CR], test echo disabled

[CR], test echo enabled

[CR,LF], test echo disabled

[CR,LF], test echo enabled

no terminator, test echo disabled

no terminator, test echo enabled

When the test echo is on, every character transmitted or received via the GPIB port is
echoed to the RS232 port. This is provided solely as an aid to program development
and should not be enabled during normal operation of the instrument.

Содержание 7220



























































































































































Результаты поиска

Содержание 7220

Отзывы:

Похожие инструкции для 7220

Бренды по названию

Популярные бренды

IBM 7220, Инструкция по эксплуатации

Результаты поиска

Содержание 7220

Отзывы:

Похожие инструкции для 7220

Бренды по названию

Популярные бренды