IBM 7220 Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 155

background image

WARRANTY

EG&G Instruments Corporation warrants each instrument of its own manufacture to be free of defects in material and
workmanship for a period of ONE year from the date of delivery to the original purchaser. Obligations under this Warranty
shall be limited to replacing, repairing or giving credit for the purchase, at our option, of any instruments returned, shipment
prepaid, to our Service Department for that purpose, provided prior authorization for such return has been given by an
authorized representative of EG&G Instruments Corporation.

This Warranty shall not apply to any instrument, which our inspection shall disclose to our satisfaction, to have become
defective or unusable due to abuse, mishandling, misuse, accident, alteration, negligence, improper installation, or other
causes beyond our control. This Warranty shall not apply to any instrument or component not manufactured by EG&G
Instruments Corporation. When products manufactured by others are included in EG&G Instruments Corporation equipment,
the original manufacturers Warranty is extended to EG&G Instruments customers.

EG&G Instruments Corporation reserves the right to make changes in design at any time without incurring any obligation to
install same on units previously purchased.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THIS WARRANTY IS
IN LIEU OF, AND EXCLUDES ANY AND ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESSED, IMPLIED OR
STATUTORY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AS WELL AS ANY AND ALL
OTHER OBLIGATIONS OR LIABILITIES OF EG&G INSTRUMENTS CORPORATION, INCLUDING, BUT NOT LIMITED TO, SPECIAL
OR CONSEQUENTIAL DAMAGES. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO ASSUME FOR EG&G
INSTRUMENTS CORPORATION ANY ADDITIONAL OBLIGATION OR LIABILITY NOT EXPRESSLY PROVIDED FOR HEREIN
EXCEPT IN WRITING DULY EXECUTED BY AN OFFICER OF EG&G INSTRUMENTS CORPORATION.

SHOULD YOUR EQUIPMENT REQUIRE SERVICE

A. Contact your local EG&G Instruments office, agent, representative or distributor to discuss the problem. In many cases it

may be possible to expedite servicing by localizing the problem to a particular plug-in circuit board.

B.

We will need the following information, a copy of which should also be attached to any equipment which is returned for
service.

1. Model number and serial number of instrument

2. Your name (instrument user)

3. Your address

4. Address to which the instrument should be

returned

5. Your telephone number and extension

C. If you experience any difficulties in obtaining service please contact

EG&G Instruments
Signal Recovery

Phone:

+44 (0)118 977 3003

Sorbus House

Fax:

+44 (0)118 977 3493

Mulberry Business Park
WOKINGHAM RG41 2GY
United Kingdom

6. Symptoms (in detail, including control settings)

7. Your purchase order number for repair charges

(does not apply to repairs in warranty)

8. Shipping instructions (if you wish to authorize

shipment by any method other than normal surface
transportation)

«
...
153
154
155

Содержание 7220




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7220

Бренд: Cambridge Audio Страницы: 2

Бренд: Cambridge Audio Страницы: 19

Бренд: Cambridge Audio Страницы: 14

Бренд: NAD Страницы: 2

Бренд: Cambridge Audio Страницы: 19

Бренд: Hamilton/Buhl Страницы: 16

Бренд: Hamilton Electronics Страницы: 5

Бренд: Takstar Страницы: 24

Бренд: Parasound Страницы: 20

Бренд: Atlona Страницы: 10

EVID C8.2 Ceiling

Бренд: Electro-Voice Страницы: 2

Passport Everon-G

Бренд: VXI Страницы: 1

Бренд: Crestron Страницы: 7

Бренд: One for All Страницы: 26

Бренд: JEFF ROWLAND Страницы: 15

Бренд: Yaesu Страницы: 18

Series VII Aphrodite

Бренд: Hifonics Страницы: 58

Бренд: IRT Electronics Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды