IBM 7220 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 155

background image

4-7

Chapter 4, FRONT AND REAR PANELS

4.2.03 RS232 Connector

This 9-pin D type RS232 interface connector implements pins 1, 2, 3 and 7 (Earth
Ground, Transmit Data, Receive Data, Logic Ground) of a standard DTE interface.
To make a connection to a PC-compatible computer, it is normally sufficient to use a
three-wire cable connecting Transmit Data to Receive Data, Receive Data to
Transmit Data, and Logic Ground to Logic Ground. Appendix D shows the
connection diagrams of cables suitable for computers with 9-pin and 25-pin serial
connectors. Pinouts for this connector are given in appendix B.

4.2.04 AUX RS232 Connector

This connector is used to link other compatible EG&G equipment together in a
“daisy-chain” configuration. Up to an additional 15 units can be connected in this
way. Each unit must be set to a unique address (see section 5.2.08). Pinouts for this
connector are given in appendix B.

4.2.05 GPIB Connector

The GPIB interface connector conforms to the IEEE-488 1978 Instrument Bus
Standard. The standard defines all voltage and current levels, connector
specifications, timing and handshake requirements.

4.2.06 DIGITAL OUTPUTS Connector

This connector provides eight TTL output lines, each of which can be set high or low
by the use of a front panel setup menu or via the computer interfaces. It is most
commonly used for controlling auxiliary apparatus, such as lamps, shutters and
heaters. Pinouts for this connector are given in appendix B.

4.2.07 PREAMP POWER Connector

This connector supplies ±15 V at up to 100 mA and can be used for powering any of
several optional remote preamplifiers available from EG&G Instruments. Pinouts for
this connector are given in appendix B.

4.2.08 REF MON Connector

The signal at this connector is a TTL-compatible waveform synchronous with the
reference. This output monitors correct reference channel operation but its polarity is
not uniquely defined so that it does not necessarily show the correct phase
relationship with the SIG MON output.

4.2.09 REF TTL Connector

This connector is provided to allow TTL compatible pulses to be used as the
reference input.

4.2.10 SIG MON Connector

The signal at this connector is that immediately prior to the main analog to digital
converter and after the preamplifier, line filter and anti-alias filters.

«
...
37
38
39
40
41
...
»

Содержание 7220




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7220

Бренд: Samson Страницы: 2

Бренд: Pangea Страницы: 7

Бренд: Gainlab Audio Страницы: 15

Бренд: XINDAK Страницы: 10

Бренд: JBL Страницы: 28

Бренд: HAMTRONICS Страницы: 3

Бренд: Crest Audio Страницы: 18

Бренд: Analog Devices Страницы: 20

Бренд: Link electronics Страницы: 2

Бренд: Advance Paris Страницы: 16

Бренд: Randall Страницы: 10

Бренд: Fender Страницы: 11

Бренд: Laney Страницы: 12

Бренд: Camco Страницы: 42

Бренд: Studiomaster Страницы: 6

IM18-DI03-4S-5R-S Series

Бренд: turck Страницы: 8

Бренд: Boss Audio Systems Страницы: 11

Бренд: soundsation Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды