IBM 7220 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 155

background image

6-28

Chapter 6, COMPUTER OPERATION

bit number

bit negated

bit asserted

0

data + parity = 8 bits

data + parity = 9 bits

1

no parity bit

1 parity bit

2

even parity

odd parity

3

echo disabled

echo enabled

4

prompt disabled

prompt enabled

GP [n

1

[n

2

]] Set/read GPIB parameters

n

1

sets the GPIB address in the range 0 to 31

n

2

sets the GPIB terminator and the test echo function according to the following

table:

n

Terminator

0

[CR], test echo disabled

1

[CR], test echo enabled

2

[CR,LF], test echo disabled

3

[CR,LF], test echo enabled

4

no terminator, test echo disabled

5

no terminator, test echo enabled

When the test echo is on, every character transmitted or received via the GPIB port is
echoed to the RS232 port. This is provided solely as an aid to program development
and should not be enabled during normal operation of the instrument.

\N n

Address command

When the model 7220 is daisy-chained with other compatible instruments this
command will change which instrument is addressed. All daisy-chained instruments
receive commands but only the currently addressed instrument will implement or
respond to the commands. The exception is the \N n command. If n matches the
address set from the front panel the instrument will switch into addressed mode. If n
does not match the address set from the front panel the instrument will switch into
unaddressed mode.

Note: The \N n command does not change the address of an instrument but which
instrument is addressed.

Warning: All instruments must have a unique address.

DD [n]

Define delimiter control

The value of n, which can be set to 13 or 32 to 125, determines the ASCII value of
the character sent by the lock-in amplifier to separate two numeric values in a two-
value response, such as that generated by the MP (magnitude and phase) command.

ST

Report status byte

Causes the lock-in amplifier to respond with the status byte.

Note: this command is not normally used in GPIB communications, where the status

«
...
102
103
104
105
106
...
»

Содержание 7220




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7220

Бренд: NAD Страницы: 2

Бренд: Jensen Страницы: 6

Бренд: Fender Страницы: 32

Бренд: Fender Страницы: 4

Hot Rod DeVille

Бренд: Fender Страницы: 2

Бренд: Fender Страницы: 12

Бренд: Fender Страницы: 16

Blues Deluxe Reissue

Бренд: Fender Страницы: 16

Acoustasonic SFX

Бренд: Fender Страницы: 20

Acoustasonic 30

Бренд: Fender Страницы: 8

Bassman Bassman 100

Бренд: Fender Страницы: 16

Bassman Bassman 100

Бренд: Fender Страницы: 4

Бренд: Fender Страницы: 20

Бренд: Fender Страницы: 20

Бренд: Fender Страницы: 4

65 Deluxe Reverb

Бренд: Fender Страницы: 12

Бренд: Fender Страницы: 2

Бренд: Fender Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды