5-41
J1939 Code
Description
Refer to Procedure
108-3
Barometric Pressure : Voltage Above Normal
Sensor Signal (Analog, Active) - Test
108-4
Barometric Pressure : Voltage Below Normal
Sensor Signal (Analog, Active) - Test
110-3
Engine Coolant Temperature : Voltage Above
Normal
Sensor Signal (Analog, Passive) - Test
110-4
Engine Coolant Temperature : Voltage Below
Normal
Sensor Signal (Analog, Passive) - Test
110-15
Engine Coolant Temperature : High - least severe (1) Coolant Temperature Is High
110-16
Engine Coolant Temperature : High - moderate
severity (2)
Coolant Temperature Is High
152-2
Number Of ECU Resets : Erratic, Intermittent, or
Incorrect
ECM Memory - Test
157-0
Engine Injector Metering Rail #1 Pressure : High -
most severe (3)
Fuel Rail Pressure Problem
157-2
Engine Injector Metering Rail #1 Pressure : Erratic,
Intermittent, or Incorrect
Fuel Rail Pressure Problem
157-3
Engine Injector Metering Rail #1 Pressure : Voltage
Above Normal
Sensor Signal (Analog, Active) - Test
157-4
Engine Injector Metering Rail #1 Pressure : Voltage
Below Normal
Sensor Signal (Analog, Active) - Test
157-10
Engine Injector Metering Rail #1 Pressure :
Abnormal Update Rate
Sensor Signal (Analog, Active) - Test
157-16
Engine Injector Metering Rail #1 Pressure : High -
moderate severity (2)
Fuel Rail Pressure Problem
157-17
Engine Injector Metering Rail #1 Pressure : Low -
least severe (1)
Fuel Rail Pressure Problem
157-18
Engine Injector Metering Rail #1 Pressure : Low -
moderate severity (2)
Fuel Rail Pressure Problem
166-2
Engine Rated Power : Erratic, Intermittent, or Incorrect ECM Memory - Test
166-14
Engine Rated Power : Special Instuction
ECM Memory - Test
168-3
Battery Potential / Power Input 1 : Voltage Above
Normal
Electrical Power Supply - Test
168-4
Battery Potential / Power Input 1 : Voltage Below
Normal
Electrical Power Supply - Test
172-3
Engine Air Inlet Temperature : Voltage Above Normal Sensor Signal (Analog, Passive) - Test
172-4
Engine Air Inlet Temperature : Voltage Below Normal Sensor Signal (Analog, Passive) - Test
173-3
Engine Exhaust Gas Temperature : Voltage Above
Normal
Sensor Signal (Analog, Passive) - Test
※
Some fault codes are not applied to this machine.
Содержание HX130 LCR
