Hyke HK7024, Инструкции и предупреждения по установке и использованию

Страница: 11 / 36

EN
English – 9
TABLE 6 - Programming procedure (second level functions)
01. Press and hold down the “ Set ” key for approx. 3 seconds.;
02. Release the key when LED “ L1 ” starts flashing;
03. Press the “ ” or “ ” key to move the flashing LED to the LED representing the “input LED” of the parameter to be modified;
04. Press and hold the “ Set ” key through to completion of point 06;
05. Wait approx. 3 seconds, until the LED representing the current level of the parameter to be modified illuminates;
06. Press keys “ ” or “ ” to move the LED representing the value of the parameter;
07. Release the “ Set ” key;
08. Wait 10 seconds (maximum time) to exit the programming mode.
Note – During this procedure, points 03 to 07 need to be repeated when programming other parameters during the phase itself.
SET
SET
SET
SET
L1
o
or
3 s
10 s
6.3 - Special functions
6.3.1 - Function: “Move anyway”
This function allows the automation to be operated even when any of the safe-
ty devices does not work correctly or is out of use.
The automation can be controlled in the “
hold-to-run ” mode. Proceed as follows:
01. Send a command to operate the gate using a transmitter or a key selector,
etc. If everything operates correctly, the gate will move normally, otherwise
proceed as follows;
02. within 3 seconds, activate the control again and keep it activated;
03. after approximately 2 seconds, the gate will perform the required move-
ment in “
hold-to-run ” mode; i.e. the gate will continue to move only as long
as the control is activated.
If the safety devices do not operate, the flashing light flashes a few times to indi-
cate the kind of problem (see chapter 6 - Table 8).
6.3.2 - Function: “Maintenance warning”
This function serves to indicate when the automation requires maintenance.
The maintenance warning signal is given by way of a lamp connected to the
S.C.A. (open gate light) output when this output is programmed as “Mainte-
nance light”. The various warning lamp signals are shown in
Table 7 .
To program the limit value of the maintenance operations, see Table 5 .
Some devices are able to emit signals that serve to recognise their state of
operation or possible faults.
If a flashing light is connected to the FLASH output on the control unit, it will
flash at intervals of 1 second during a manoeuvre. If faults occur, the flashing
light will emit a sequence of two shorter flashes separated by a 1 second
pause.
Table 8 shows the cause and solution for each type of signal.
The LEDs on the control unit also emit signals.
Table 9 shows the cause and solution for each type of signal.
It is possible to verify faults that have occurred during the last 8 manoeuvres.
See
Table 10 .
WHAT TO DO IF…
(troubleshooting guide)
7
Table 7 - “Maintenance light”
Number of manoeuvres Signal
Light on for 2 seconds at the start of the opening
manoeuvre.
Light flashing for the entire duration of the manoeuvre.
Light flashing continuously.
Below 80% of the limit
Between 81% and
100% of the limit
Beyond 100% of the limit
6.4 - Deleting the memory
To delete the control unit memory and restore all factory settings, proceed as
follows:
press and hold keys “ ” and “ ” until leds L1 and L2 start flashing.
Note – The factory settings are highlighted in grey.
L8 L1
L2
L3
L4
L5
L6
L7
L8 Manoeuvre 1 result (most recent)
Manoeuvre 2 result
Manoeuvre 3 result
Manoeuvre 4 result
Manoeuvre 5 result
Manoeuvre 6 result
Manoeuvre 7 result
Manoeuvre 8 result The type of fault that has occurred in
the last 8 manoeuvres can be establi-
shed
See TABLE 10 – Fault log.
List of
faults
L7 L1
L2
L3
L4
L5
L6
L7
L8 500
1000
1500
2500
5000
10000
15000
20000 Controls the number of manoeuvres:
when this number is exceeded, the
control unit signals an automation
maintenance request; see paragraph
6.3.2. – Maintenance warning. Mainte-
nance
warning