Hyke HK7024, Инструкции и предупреждения по установке и использованию

Страница: 15 / 36

EN
English – 13
TECHNICAL SPECIFICATIONS OF PRODUCT
HK7224K
Electromechanical gearmotor for automations of gates and
automatic doors with DC motor, epicyclical gear reducer and
mechanical release.
HK7024K
Electromechanical gearmotor for automations of gates and
automatic doors with DC motor, epicyclical gear reducer and
mechanical release. Built-in control unit and OXI radio receiver.
Type
Maximum torque 500 Nm
Nominal torque 120 Nm
Speed under no load 2.25 RPM
Speed at nominal torque 2.00 RPM
Maximum cycle frequency 40 cycles/hour
Maximum continuous cycle time approx. 7 minutes
Application limits the product can be used on gates with leaf weights up to 330 kg for lengths up to 1.8m or 200 kg
for lengths up to 3.5m (see graph 1)
Lifetime estimated between 150,000 cycles and 500,000 cycles, according to the conditions stated in table 13 and graph 3
Assembly Vertical, with dedicated fixing plate
Operating temperature from -20°C to +50°C (at low temperatures, gearmotor efficiency is reduced)
se in acid, saline or
potentially explosive
NO
atmospheres
Protection rating IP 54 (with container intact)
Dimensions (mm) 210 x 290 x 320 h
Weight (kg) 10.5 Kg; 9.5 Kg
Notes :
(1) - Function can be activated with Oview programmer.
[*] - The outputs Flashing Light, Electric lock and Gate Open Indicator can be programmed with other functions (see “TABLE 3 – Level 1 functions”; or via the Oview programmer; see
chapter 8.3). The electrical specifications of the output are adapted to the type of selected function: • flashing light function: lamp 12 Vdc, max. 21 W; • electric lock function: 12 Vac
max. 15 VA; • other outputs (all types): 1 lamp or relay 24Vdc (-30 to +50%), max. 4 W.
Power supply 230 Vac (120 Vac for version HK7024K/V1 ) 24 Vdc (±10%)
±10%; 50/60 Hz
Backup power supply Provision for buffer battery PS124
Solar power provision for SYKCE kit
Maximum absorbed power 300 W 140 W
Maximum absorbed current 1,5 A (3 A for version HK7024K/V1 ) 6 A for a maximum interval of 2 s
Absorbed power with
“All – Standby (1)” function
when powered by PS124
less than 100 mW
or SYKCE kit (including
OXI receiver)
Flashing light output [*] one LUCYB flashing light (12 V, 21 W bulb)
Electric lock output [*] one 12 Vac electric lock (max 15 VA)
Gate open indicator output [*] one 24 V lamp (max. 4 W) (the output voltage
may vary between -30 and +50%, the output can
also control small relays)
BLUEBUS output one output with load of maximum 15 Bluebus
units (max. 6 pairs of MOFB or MOFOB photocells plus
2 pairs of MOFB or MOFOB photocells routed
as opening devices plus max. 4 MOMB
or MOTB control devices)
STOP input for normally closed contacts, normally open
contacts or contacts with constant 8,2 k
Ω
resistance;
selection of the type of contact is in self-learning
mode and a modification with respect to the memorised
status will generate a “STOP”
SS input for normally open contacts (closure of the contact
generates a Step Step command)
Radio engage SM connector for receivers in the families SMXI,
OXI and OXIFM
Radio AERIAL input 50
Ω
for cable type RG58 or similar
Programmable functions 8 ON-OFF type functions (Table 3) and
8 settable functions (Table 5)
Functions in self-learning • Self-learning of devices connected to the BlueBus output.
• Self-learning of the type of device connected to the “STOP”
terminal (NO, NC contact or 8,2 k
Ω
resistance).
• Self-learning of the gate leaf travel and automatic
calculation of deceleration points and partial opening.
• Self-learning of operation with one or two motors
WARNINGS: • All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C). • Nice S.p.a. reserves the right to apply modifi-
cations to products at any time when deemed necessary, maintaining the same intended use and functionality.