HYDAC International FCU 2110-5 Скачать руководство пользователя страница 21

Страница: 21 / 52

Operating and Maintenance Instructions : FCU 2110-5 / FCU 2210-5

Edition 1.10

HYDAC Filtertechnik GmbH

Page 21 of 52

5.6.3 Relay Functions

Function mode

Relay 1

Relay 2

M1: Measure

Contacts 7 and 8 are closed
when measurement has started
and is ongoing.

Contacts 6 and 8 are closed
when the FCU is not in service.

Contacts 14 and 15 are
closed when a flow rate
error has been detected

M2: M switch

Has to be set to flow rate / fall
below /

↓

149 ml

↑

150ml to

open internal shut-off valve !

Contacts 14 and 15 are
closed when the user has
programmed valid setting
values.

Contacts 13 and 15 are
closed when the user has
programmed invalid setting
values.

M3: Filter to

Contacts 7 and 8 are closed
when measurement has been
started and the measured
values (purity ratings) are not
within the range (limits)
programmed by the user.

Contacts 6 and 8 are closed
when 5 measurements in a row
are identical to the limit
programmed by the user or are
below it.

Not in operation

M4: Filter from to

Contacts 6 and 8 are closed
when 5 measurements in a row
are identical to the limit
programmed by the user or are
below it.

Contacts 7 and 8 are closed
when:

−

Measurement has been

started and the
measurement results of the
purity rating are below the
lower limit specified by the
user.

−

Measurement cycle is in

progress and the
measurement results of the
purity ratings are above the
upper limit specified by the
user.

Not in operation

Содержание FCU 2110-5





















































Результаты поиска

Содержание FCU 2110-5

Отзывы:

Похожие инструкции для FCU 2110-5

Бренды по названию

Популярные бренды

HYDAC International FCU 2110-5, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FCU 2110-5

Отзывы:

Похожие инструкции для FCU 2110-5

Бренды по названию

Популярные бренды