Huvema HU 320 UM TOPLINE, Руководство пользователя

Страница: 5 / 64

5
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
T-slots 14 x 63 / 2 no Frequency 50 Hz
Main Drive (IEC-three phase motor (IP54))
Max. Voltage fluctuations + 6 / -10%
Power at 100/40% ED 2.2 / 3.0 kW Terminal value 4.0kVA
Rated engine speed 1750 U / min Fuse for the machine 11 A carrying
Torque at 1750 rev / min 285 Nm Machine Dimensions
Feed Drive
Length 1200 mm
Feed force 1600 N Width 1300 mm
Speed continuously 10-450 U / min Height 1800 mm
Rapid traverse 680 mm / min Weight ca. 1267 kg
Horizontal Milling Spindle Operating Conditions
Tool Holder ISO-40 Required ambient temperature + 10 ° C to + 35
° C
Mechanical speed stages 12 SPL
Speed Range 50-2,000 U / min Max. Sound pressure level 80 dB (A)
Swiveling Vertical Milling
In the following conditions:
- Enveloping surface measuring method
according to DIN 45635
- Operating mode: maximum speed at idle
- Measuring point: 1m distance and 1,6m
above ground
Tool Holder ISO-40
Quill Travel 120 mm
Swivel Range ± 90 °
Speed Steps 12
Speed Range 50-2,000 U / min
3.2 M
aCHine Takeover
Observe the following for machine acquisition
Notes
• Clear width of doors sufficient?
• Only supply hoists with sufficient carrying capacity contact
(see Transport).
• Machine for any transport damage before arrives. Falls
damage can be detected.
• If damage is found, immediately dealers contact the insurance
company.
• Machine is complete the scope of supply.
Check
Such as the machine base, machine column, up clamping table,
spindle headstock w/ horizontal
spindle, angle table and slides, automatic Feed drives for the X
axis (longitudinal) and Y axis
(transverse), removable chip tray, electrical cabinet, drive engine,
cooling system, protective cap for
clutch system etc.
Tool box included the flat & cross point screw drivers, grease gun,
set of hex wrenches, special
handles, ISO40/MT-3 sleeve, MT-1 & MT-2 adapter and pads &
bolts, manual, spare parts list etc.
Reference
The basic equipment can be extended depending on the country
of delivery. Contact for lack orambiguity dealer.
Noted
Take care, if your machine has been packed with a plastic cover,
this carefully from the machineand store it as a dust cover for the
machine during longer downtimes. Transport of the machine
1-
4.
M
ach
in
e t
akeo
ve
r
O
bs
er
ve t
he
fol
low
ing
for
m
ac
hi
ne
ac
qui
sition
No
tes:
- C
lear
w
idt
h of
do
or
s s
uffi
cient
?
- O
nl
y s
uppl
y hoi
sts
w
ith s
uffi
cie
nt
c
ar
ryin
g c
apac
ity
c
ont
ac
t (
see
Tra
ns
por
t).
-
M
ac
hi
ne
for
a
ny
trans
por
t d
am
ag
e be
for
e
ar
riv
es
. F
alls
dam
ag
e c
an
be
det
ec
ted.
If da
m
ag
e i
s fou
nd,
im
m
edi
atel
y deal
er
s c
ont
ac
t th
e i
ns
ur
anc
e c
om
pa
ny
.
- M
ac
hi
ne i
s c
om
pl
et
e the s
cope
o
f s
uppl
y
Ch
ec
k:
S
uc
h
as
th
e
m
ac
hi
ne
bas
e,
m
ac
hi
ne c
ol
um
n, up c
lam
ping
tabl
e,
s
pi
ndl
e
hea
ds
toc
k w
/ hor
izont
al
spi
ndl
e,
ang
le t
abl
e
an
d s
lides
, aut
om
at
ic F
eed dr
ives
for
the X
ax
is (
long
itudi
nal
) a
nd Y
ax
is
(trans
ver
se)
, r
em
ov
abl
e c
hi
p t
ray
, el
ec
tric
al
c
abi
ne
t, dr
ive eng
ine,
c
ool
ing
s
ys
tem
, pr
ot
ec
tiv
e c
ap
for
clu
tch
sy
st
em
e
tc.
To
ol
box
inc
lud
ed
the
flat
&
c
ros
s p
oi
nt
s
cre
w dr
iver
s, gr
eas
e g
un,
set
o
f hex
w
renc
hes
, s
pec
ial
han
dl
es
, IS
O
40/
M
T-3
sleev
e,
M
T-1
& M
T-2
a
dapt
er
an
d p
ads
&
b
ol
ts, m
anu
al
, s
par
e p
ar
ts l
ist et
c.
Ref
er
en
ce
:
Th
e b
as
ic eq
ui
pm
en
t c
an b
e ex
ten
ded
de
pe
ndi
ng
on t
he c
oun
try
of
del
iver
y. C
ont
ac
t for
la
ck
or
am
bi
gui
ty deal
er
.
No
te
d:
Tak
e c
ar
e, i
f y
our
m
ac
hi
ne
has
b
ee
n
pac
ke
d
wit
h a p
las
tic
c
ov
er
, thi
s c
ar
eful
ly f
rom
the
m
ac
hi
ne
and s
tor
e i
t as
a
dus
t c
ov
er
for
the
m
ac
hi
ne
d
ur
ing
long
er
dow
nt
im
es
.
7