manualshive.com logo in svg

HUSTLER Super Z HD, Общее руководство по обслуживанию, Страница: 49 / 50

Поделиться
Скачать
HUSTLER Super Z HD Скачать руководство пользователя страница 49

117592

1-1

REV C

INDEX

PAGE

PAGE

Belts.................................................................. 4-5

, 

6-4

Blades....................................................................... 6-3

Control lever stops .................................................. 4-2

Deck Belt adjustment .............................................. 6-4

Deck Belt Routing & Tensioning............................. 6-8

Deck leveling............................................................ 6-1

Electrical Schematic – Briggs & Stratton ............... 7-4

Electrical Schematic – Kawasaki.................... 7-1

, 

7-2

Electrical Schematic – Kawasaki DFI .................... 7-3

Engine air filter......................................................... 5-1

Engine oil and filter.................................................. 5-1

Engine RPM settings ............................................... 5-5

Fuel & evaporative system line routings ................ 5-3

Fuel evaporation system filter ................................ 5-3

General engine maintenance.................................. 5-1

General maintenance precautions ......................... 2-2

Hydraulic pump belt adjustment ............................. 4-5

Hydraulic system ..................................................... 4-6

Maintenance introduction........................................ 1-1

Maintenance precautions ........................................2-2

Maintenance schedule ............................................8-1

Mower blade maintenance ......................................6-3

Mower blade removal ..............................................6-3

Operate machine safely ..........................................2-2

Operation precautions .............................................2-2

Pre-operation precautions.......................................2-1

Rear Discharge Deck Belt Routing & Tensioning .6-7

Safe servicing practices ..........................................2-1

Service Program ......................................................1-1

Side Discharge Deck Belt Routing & Tensioning ..6-6

Special torques ........................................................3-1

Standard torques .....................................................3-1

Steering adjustments...............................................4-1

Steering control lever adjustment...........................4-4

Steering control lever neutral adjustment ..............4-1

Steering damper ......................................................4-3

Warner Clutch Re-gap Adjustment Procedures ..4-11

Warranty ...................................................................1-1

Содержание Super Z HD



















































Отзывы:

Нет отзывов