HUSTLER Super Z HD Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 50

HUSTLER Super Z HD Скачать руководство пользователя страница 22

REV C

4-10

117592

to half throttle and stroke the steering control lever
forward and reverse several times until the wheel motor
operates smoothly through the entire speed range.

13.

IMPORTANT:

With the engine off, disconnect the two

female spade connectors from each other (from step #3)
and reconnect them to the seat switch. This must be
completed so that the safety circuit is functioning
properly. Figure 4-26 & Figure 4-27

14.

Check to make sure all tools or obstructions are removed

Figure 4-25

Prefill
pump

here

Right side pump

Prefill
pump

here

Left side pump

WARNING

Do not operate the mower without plugging the mower’s
wiring harness into the seat switch. This switch is an
important part of the safety start interlock system. Serious
injury can result if the seat switch is not plugged into the
mower’s wiring harness.

WARNING

Never operate the mower with a non-functioning seat
switch. Always reconnect the seat switch to the mower
harness.

Figure 4-26

Figure 4-27

Mower

harness

Seat

switch

Female
spades

Mower

harness

Female
spades

«
...
20
21
22
23
24
...
»

Содержание Super Z HD



















































Отзывы:

Нет отзывов