HUSTLER Super Z HD Скачать руководство пользователя страница 27

Страница: 27 / 50

117592

5-3

REV C

Carbon canister

Some Hustler

Super Z HD mowers will have a carbon

canister incorporated into the fuel system. Figure 5-5

This is a mandatory feature that is required on all mowers

using gasoline engines that are put into operation in California.

These canisters should be replaced every 5 years or if they

become damaged.

Fuel evaporation system filter

Some Super Z

HD mowers have a fuel evaporation system

filter. This filter must be checked and replaced every 500 hours
or annually whichever comes first. Figure 5-6

Fuel & evaporative system line routings

There are two rubber hoses that are connected to the fuel

tanks. One is the fuel hose that is part of the fuel system. The
other is the vapor line that is part of the fuel evaporative system.

The fuel hose is connected to the fuel tank as shown. It

connects the fuel tank to the fuel shutoff valve. Figure 5-7

The vapor line is connected to the fuel tank as shown. It

connects the fuel tank to the engine’s vapor port. Figure 5-8 &
Figure 5-8

Figure 5-5

Figure 5-6

Carbon

canister

Fuel evaporation

system filter

Fuel evaporation

system filter

Carbon

canister

Fuel evaporation

system filter

Figure 5-7

Figure 5-8

Fuel line

Fuel

shutoff

valve

Fuel
tank

Fuel line

Seat support

Fuel evaporation

system filter

Vapor line

Tee

Fuel
tank

Tee

Vapor line

Содержание Super Z HD



















































Результаты поиска

Содержание Super Z HD

Отзывы:

HUSTLER Super Z HD, Общее руководство по обслуживанию, Страница: 27 / 50

Результаты поиска

Содержание Super Z HD

Отзывы: