background image

Hussmann® Impact™ Hot Food Merchandiser 

Introduction 

 

 

Safe Work Practices 

 

 

Beware of High Voltage  

 
This equipment uses high voltage. Serious injury can occur if you or 
any untrained or unauthorized person installs, services, or repairs this 
equipment. Always Use an Authorized Service agent to Service Your 
Equipment 

 

Keep this manual with the Equipment  

 
This manual is an important part of your equipment. Always keep it 
near for easy access. 

 

If you need to replace this manual, contact: 
 

BKI 

Technical Services Department 
P.O. Box 80400 
Simpsonville, S.C.  29680-0400 
Or call toll free: 1-800-927-6887  
Outside the U.S., call 864-963-3471 

 

Protect Children  
 

Keep children away from this equipment. Children may not understand 
that this equipment is dangerous for them and others. 
 
NEVER allow children to play near or operate your equipment. 

 

Keep Safety Labels Clean and in Good Condition 
 

Do not remove or cover any safety labels on your equipment. Keep all 
safety labels clean and in good condition. Replace any damaged or 
missing safety labels. Refer to the Safety Labels section for illustration 
and location of safety labels on this unit. If you need a new safety 
label, obtain the number of the specific label illustrated on page 5, 
then contact: 
 

BKI 

Technical Services Department 
P.O. Box 80400 
Simpsonville, S.C.  29680-0400 
Or call toll free: 1-800-927-6887  
Outside the U.S., call 864-963-3471 

Содержание SSWHI

































Отзывы: