background image

Hussmann® Impact™ Hot Food Merchandiser 

Maintenance 

 

 

25 

Maintenance 

 

 

Failure to comply with the maintenance below could result in a serious accident.   

 

Electrocution, equipment failure or property damage could result if an unlicensed 
electrician performs electrical repair. Ensure that a licensed electrician performs 
electrical repair. 

Scheduled Maintenance  

Use the following table to help manage scheduled maintenance activities. 
 

Frequency Performed 

By 

Part 

Activity 

Daily 

User 

Case 

Clean the entire Case. Refer to the 
cleaning procedure below.  

Cleaning 

This unit should be cleaned at the end of each day. Use the following procedure: 
 

 

Failure to remove power from this unit may cause severe electrical shock. This 
unit may have more than one disconnect switch. 

 

1.  Turn the machine ‘off ‘ and allow it to cool down. 

 

2.  Remove any food pans. 

 

 

Using abrasive cleaners may damage the cabinet finish. Use only a mild soap 
and water solution. 
 
Never steam clean or get excess water in the interior of the cabinet as this can 
damage unit.  

 

3.  Use a mild soap and water solution to clean parts. 

 

4.  Sponge the inside and outside with a mild soap and water solution. 

 

5.  Wipe the parts and cabinet dry with a soft, clean cloth. 

Содержание SSWHI

































Отзывы: