background image

IGSV-ASCS-0303

12

Electrical

WIRING COLOR CODE

G R E E N

G RO U N D

P U R P L E

A N T I - S W E AT

O R A N G E

L I G H T S

Y E L L OW

R E C E P TA C L E

R E D   /   B L A C K  

T- S TAT   / S O L E N O I D 230V

BLACK / WHITE

T- S TAT   /   S O L E N O I D   115V

B ROW N

FAN MOTORS

CASE MUST BE GROUNDED

NOTE: Refer to label affixed to case to determine the actual

configuration as checked in the “TYPE INSTALLED” boxes.

ELECTRICAL CIRCUIT IDENTIFICATION

Standard lighting for all models will be full length fluorescent
lamps located within the case at the top.
The switch controlling the lights, the plug provided for digital
scale, and the thermometer are located at the rear of the case
mullion.
The receptacle that is provided on the exterior back of these
models is intended for computerized scales with a five amp
maximum load, not for large motors or other high wattage
appliances. It should be wired to a dedicated circuit.

CASE-TO CASE CONNECTORS

HUSSMANN/CHINO now provides “CASE-TO-CASE”
locking electrical connector fittings on the ASCS service cases.
These connectors greatly simplify field installation thereby saving
time and electrical installation costs.

NOTE:  The total case electrical draw must not exceed
30 Amps ampacity at 115V in one connected lineup.

ELECTRICAL SERVICE RECEPTACLES
(WHEN APPLICABLE)

The receptacles located on the exterior of the
merchandiser are intended for scales and lighted displays.
They are not intended nor suitable for large motors or
other external appliances.

BEFORE SERVICING

Always Disconnect Electrical

Power at the Main Disconnect

when servicing or replacing any

electrical component.

This includes (but not limited to) Fans, Heaters,

Thermostats, and Lights.

FIELD WIRING AND SERIAL PLATE AMPERAGE

Field wiring must be sized for component amperes printed
on the serial plate. Actual ampere draw may be less than
specified. Field wiring from the refrigeration control panel
to the merchandisers is required for refrigeration
thermostats. Most component amperes are listed in the
“Case Specs” section, but always check the serial plate.

BALLAST LOCATION

Ballasts are located within the access panel that runs the
length of the rear of the case. Refer to diagram on  page 6.

WIRING AND SERIAL PLATE AMPERAGE

Field wiring must be sized for component amperes stamped
on the serial plate.  Actual ampere draw may be less than
specified. Field wiring from the refrigeration control panel to
the merchandisers is required for refrigeration thermostats.
Most component amperes are listed in the "Case Specs" section,
but always check the serial plate.

ASHRAE COLOR CODE

NOTE: All other manufacturers; no known sensor codes

Case Control Systems

SENSOR COLORS

Manufacturer ® >

EIL

CPC

Location

Coil Inlet

Color

Blue

Blue

Part#

225-01-1755

225-01-3255

Coil Outlet

Color

Red

Red

Part#

225-01-1757

225-01-3123

Discharge Air

Color

Green

Green

Part#

225-01-1756

225-01-3260

Return Air

Color

Purple

Green

Part#

225-01-1758

225-01-3260

Defrost Term.

Color

White

Orange

Part#

225-01-0650

225-01-3254

Liquid Line

Color

White

Blue

Part#

225-01-0650

225-01-3255

Содержание ASCS









































Отзывы: