Husqvarna SG13 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 48

background image

CONTROLS

22

Throttle

The lever controls engine speed.
With the lever down, the engine runs at idle and
functions as start position.
When the engine speed increases, the centrifugal
clutch drive automatically engages the cutting wheel.

Operator Presence (OP) Grip Bar

The bar must be held against the handle for the
engine to run. If the grip is released, the ignition
system short-circuits and the engine stops.

Control Panel On/Off Engine Switch

The ON/OFF engine switch can be used to stop the
engine. The illustration shows the toggle switch in the
OFF position (short circuited electrical system).
A second switch with the same function is activated
by the OP grip bar.
To start the engine, the control panel switch must be
set to the ON position and the OP grip bar must be
held in.

WARNING!

Do not over-ride the safety system
by binding the bar to the handle.

8064-010

8064-011

8064-012

«
...
20
21
22
23
24
...
»

Содержание SG13

















































Отзывы:

Нет отзывов

Похожие инструкции для SG13

Бренд: Baratza Страницы: 24

Бренд: Baratza Страницы: 2

Бренд: DAB Страницы: 121

Noviomagus Micro Mill

Бренд: SPIERINGS Страницы: 2

Бренд: Fellow Страницы: 23

Бренд: Ingersoll-Rand Страницы: 56

Бренд: Scarlett Страницы: 16

Бренд: Atlas Copco Страницы: 16

Бренд: Hitachi Koki Страницы: 80

Бренд: Silvercrest Страницы: 52

Бренд: Silvercrest Страницы: 74

Бренд: Sanremo Страницы: 31

Бренд: Batavia Страницы: 34

Бренд: ADE Страницы: 64

Бренд: Chicago Electric Страницы: 14

Бренд: zassenhaus Страницы: 52

Coffee Bar DCg-20 Series

Бренд: Cuisinart Страницы: 12

Бренд: Salton Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды