Husqvarna SG13 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 48

background image

MAINTENANCE

33

IMPORTANT INFORMATION

If pulley on cutter head shaft must be moved,
the set screws MUST be fully removed, fresh
Loctite 242

®

put on threads and retorqued to

100 - 110 in./lbs. (11.30 / 12.43 Nm).

8011-228

B

A

5. Loosen the locking nuts (A) on the two tension

bolts.

6. Turn the two tension bolts (B) counter-clockwise to

loosen the belt or clockwise to tighten it.

7. Check that the pulleys are aligned using a straight

edge along the inside face of the clutch and
pulley. Pulleys must be in line. Maximum gap or
misalignment is

1

/

16

" (.062) or 15.7 mm. Adjust

using the tension bolts as necessary. Recheck
belt tension.

8. Tighten all screws and nuts when the adjustment

is complete. Be certain cover plate is not rubbing
against cutter wheel shaft.

9. Refit the belt guard.

8011-229a

Check clutch and pulley alignment using inside face

WARNING!

The cutters can come loose from
the cutting wheel if the bolts are not
sufficiently tight. Comply with the
recommended torque settings.

Cutting Wheel

Tighten the screws to 30 ft/lbs. (40.67 Nm).
NOTE: The cutter teeth each have three cutting sides.
Individual teeth may be repositioned twice before
replacement is necessary.

8064-015

Tooth cutter (carbide face)

«
...
31
32
33
34
35
...
»

Содержание SG13

















































Отзывы:

Нет отзывов

Похожие инструкции для SG13

Бренд: Fein Страницы: 200

Бренд: JBM Страницы: 36

Бренд: Meec tools Страницы: 32

Бренд: Maestro Страницы: 36

Бренд: ADEO Services Страницы: 95

Бренд: Farberware Страницы: 8

Бренд: KEF Страницы: 17

Бренд: Livoo Страницы: 10

Бренд: Drill Master Страницы: 20

Бренд: Parkside Страницы: 66

Бренд: gourmetmaxx Страницы: 48

Бренд: Parkside Страницы: 77

Бренд: Parkside Страницы: 112

Бренд: SUHNER Страницы: 40

Бренд: Fiorenzato Страницы: 48

Бренд: Fiorenzato Страницы: 5

Бренд: Jet Страницы: 20

Бренд: Parkside Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды