Husqvarna SG13 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 48

background image

OPERATION

25

Starting The Engine

Check that all daily maintenance as described in the
maintenance schedule has been performed. Check
that there is sufficient fuel in the tank.

Fuel valve

Open the fuel valve. Push the lever fully to the right.

Choke control

When starting the engine warm, the lever should be in
the right position; see the illustration.
When starting the engine cold or partially warm, place
the lever completely or partly to the left. Move the
lever back to the right once the engine starts. When
the engine is cold, it may be best to move the lever
back in several stages. Find the position where the
engine runs smoothly.

Throttle

Set the throttle on the handle to the SLOW (START) /
DISENGAGE position.

8060-024b

8060-024b

8064-011

«
...
23
24
25
26
27
...
»

Содержание SG13

















































Отзывы:

Нет отзывов

Похожие инструкции для SG13

Бренд: WM Страницы: 70

Бренд: Universal Tool Страницы: 9

Бренд: HIKOKI Страницы: 76

Бренд: MSW Motor Technics Страницы: 17

Colovos 351.231060

Бренд: Craftsman Страницы: 8

evolv 900.24543

Бренд: Craftsman Страницы: 23

Professional 152.220180

Бренд: Craftsman Страницы: 32

Бренд: Feel-Maestro Страницы: 84

Бренд: Aurora Страницы: 12

Бренд: ARO Страницы: 76

Бренд: Chicago Pneumatic Страницы: 32

Бренд: Proxxon Страницы: 10

Бренд: stayer Страницы: 80

Бренд: PTA Страницы: 4

Бренд: allen Страницы: 23

Бренд: Kinu Страницы: 12

Бренд: 909 Страницы: 14

Бренд: Fiorenzato Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды