Husqvarna SG13 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 48

background image

SAFETY

12

Fuel System

Only store fuel in containers approved for that
purpose.
Never remove the fuel cap and fill the fuel tank when
the engine is running.
Always stop the engine when refueling.
Do not smoke when filling the gasoline tank and do
not pour gasoline in the vicinity of sparks or open
flame.
Never fill the fuel tank indoors.
Before starting the machine after refueling, it should
be moved at least 10 feet (3 M) from the location
where it was filled.
Turn off the fuel supply for storage or transport.
If leaks arise in the fuel system, the engine must not
be started until the problem has been resolved.
Check the fuel level before each use and leave space
for the fuel to expand. Heat from the engine and sun
can cause the fuel to expand and overflow.
Avoid overfilling. If you spill gasoline on the machine,
wipe up the spill and wait until it has evaporated
before starting the engine. Change your garments if
you spill gasoline on your clothing.

8011-205b

Never fill the fuel tank indoors.

8060-024b

Close the fuel valve.

8011-222a

Fueling always poses an element of risk

WARNING!

Gasoline and gasoline fumes
are poisonous and extremely
flammable. Be especially careful
when handling gasoline, as
carelessness can result in personal
injury or fire.

«
...
10
11
12
13
14
...
»

Содержание SG13

















































Отзывы:

Нет отзывов

Похожие инструкции для SG13

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 6

Бренд: Femi Страницы: 7

Бренд: Grizzly Страницы: 34

Бренд: Metabo Страницы: 16

Бренд: Bodum Страницы: 7

Бренд: Bodum Страницы: 93

Бренд: Ferm Страницы: 96

Бренд: Ferm Страницы: 160

Бренд: Ferm Страницы: 204

Бренд: Bifinett Страницы: 12

Бренд: Chicago Electric Страницы: 20

Бренд: Fakir Страницы: 44

Бренд: Fakir Страницы: 64

Бренд: Jet Страницы: 2

Бренд: Jet Страницы: 20

Бренд: ARENDO Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды