Husqvarna SG13 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 48

background image

17

2

1

FORWARD

5. Insert “L” end of throttle cable into the outside

hole of the engine throttle control lever.

6. Attach the throttle cable to the engine using the

double wire clamp removed in Step 1.

7. Test throttle control by pulling back throttle handle

on console. Throttle arm on engine should be
pushed completely forward. Cable should not slip
in clamp when doing this test.

8. Test proper wire length by pulling on the handle

adjustment lever and raising and lowering the
handle to maximum position without any pull on
harness.

9. Reattach air cleaner to engine.
10. Remove unit from pallet.

8060-044

1. Engine throttle control lever

2. Throttle cable

«
...
15
16
17
18
19
...
»

Содержание SG13

















































Отзывы:

Нет отзывов

Похожие инструкции для SG13

Бренд: Kela Страницы: 17

Бренд: Virutex Страницы: 20

Бренд: Kawasaki-Plastics Страницы: 4

Бренд: Central Pneumatic Страницы: 8

Бренд: Milwaukee Страницы: 142

Бренд: Parkside Страницы: 82

Бренд: Rockwell Страницы: 16

Бренд: Epiroc Страницы: 12

Бренд: Electrolux Страницы: 3

Бренд: KitchenAid Страницы: 12

Бренд: KitchenAid Страницы: 14

Бренд: KitchenAid Страницы: 52

Бренд: Bodum Страницы: 41

Бренд: Scheppach Страницы: 104

Бренд: Jet Страницы: 28

Бренд: YATO Страницы: 96

Бренд: Parkside Страницы: 66

Бренд: STEELTEC Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды