Husqvarna 966042601 Скачать руководство пользователя

Страница: 10 / 56

SAFETY

HUSQVARNA

-11

Movement/Transport

To turn and steer the machine, press down on the

•

handle and turn on the back wheels.
Turn off the engine and allow it to cool at least two

•

minutes before transport.
Fold the handle down if the machine is equipped

•

with a collapsible handle.
Use safe lifting and moving techniques when

•

loading/unloading the machine.
It is recommended that two people lift the

•

machine.
Activate the parking brake during transport.

•

Fasten the machine properly in place with

•

approved fasteners, such as tension belts, chains

or straps. Always check for compliance with

applicable traffic regulations before transporting

the machine.

Storage

Allow the engine to cool before storing the

•

machine. Never store the machine near a open

flame.

Store the machine with the fuel valve closed.

•

Store the machine and fuel in such a way that

•

there is no risk that leaking fuel or fumes can

come in contact with flames or sparks from

electrical machines, electric engines, relays,

switches, boilers or similar.
Store the machine in a locked space away from

•

children and adults untrained in its use.

Children

Serious accidents can occur if you fail to be on guard

for children in the vicinity of the machine. Never

assume that children will stay where you last saw

them.

Keep children away from the machine.

•

Keep children away from the work area and under

•

close supervision by another adult.
Shut off the machine if children enter the work

•

area.
Never allow children to operate the machine.

•

Be particularly careful near corners, bushes, trees

•

or other objects that obstruct view.

8011-278b

Lift the machine with the side handles.

8011-207c

Keep children away from the machine.

8011-206b

Never allow children to operate the machine.

Содержание 966042601

























































Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды

Husqvarna 966042601, Руководство оператора

Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды