Husqvarna 966042601 Скачать руководство пользователя

Страница: 6 / 56

SAFETY

HUSQVARNA

-7

General use

This manual is a valuable document. Read the

contents carefully before using or servicing the

machine. The following of instructions (use, service,

maintenance, etc.) by all who operate this machine is

important for the safety of the operator and others.
It can also considerably increase the life span of the

machine and increase its resale value.
Read the manual carefully and make sure you

understand it before using the machine or performing

any maintenance. If the user cannot read this manual,

it is the responsibility of the machine owner to explain

the contents to the user.
If after reading the operator’s manual you are still

unsure about the safety risks associated with use of

the machine, you should not use the machine. Please

contact your dealer for more information.
These safety instructions only address the basics

for safe use. It would be impossible in the safety

instructions to describe all possible risk situations

that could arise when using the machine. You can,

however, prevent accidents by always using common

sense.
To obtain extra copies of the operator’s manual, please

contact your dealer.

8011-208c

Read this manual carefully before starting the machine.

WARNING!
The stump grinder can be

dangerous if used improperly or

without due care. This can lead

to serious accidents or, in the

worst cases, even fatal accidents.

It is very important to read this

operator’s manual and understand

the instructions before attempting

to use the machine.

WARNING!
Under no circumstances may the

original design of the machine be

modified without written approval

from the manufacturer. Such

modifications not only affect the

performance and durability of

the machine but may even pose

a safety risk for users and those

in the vicinity. Unauthorized

modifications to the design of

the machine may absolve the

manufacturer from liability for

any resulting personal injury or

property damage. Modifying the

machine without written approval

from the manufacturer may void the

guarantee.

IMPORTANT INFORMATION
Do not use the machine until you have

read the operator’s manual carefully and

understand the instructions given. All

maintenance work or adjustments not

described in this manual must be performed

by an authorized Husqvarna service

workshop.

Содержание 966042601

























































Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды

Husqvarna 966042601, Руководство оператора

Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды