background image

CONTROLS

20 - 

HUSQVARNA

Starter

The magnapull-type starter has spring return. To 

replace the return spring or starter cord, contact an 

authorized service workshop.

Starter Handle

Misuse of the starter handle can damage the starter. 

Do not twist the starter cord around your hand.
Pull out the handle slowly until the gears mesh. Do not 

pull out the starter cord completely and do not let go of 

the starter handle when extended.

8011-127

IMPORTANT INFORMATION
Do not let the recoil cord snap back by itself. 

This may damage the cord or the recoil 

starter assembly.

WARNING!
Do not run the engine indoors, in 

enclosed or poorly ventilated spaces. 

Engine exhaust fumes contain 

poisonous carbon monoxide.

8060-024

Choke Control

The choke control opens and closes the choke valve in 

the carburetor. This is only used to start a cold engine.
If the engine is warm, the control should be in the far 

right position. 
If the engine is cold, place the lever completely or 

partly to the left. Move the lever back to the right once 

the engine starts. Forgetting the choke is evident if the 

engine runs roughly and produces black smoke.
This also results in increased fuel consumption.

Fuel Valve

The fuel valve opens and closes the connection
between the tank and the carburetor. The illustration 

shows the tank valve closed; to open, turn the lever 

completely to the right. There is no middle position.
Turn off the valve when the machine is not in use 

to avoid flooding the carburetor. The fuel valve is 

combined with a sludge reservoir. 

8060-024

Содержание 966042601

























































Отзывы: