manualshive.com logo in svg

Husqvarna 966042601, Руководство оператора

Поделиться
Скачать
Husqvarna 966042601 Скачать руководство пользователя страница 23

CONTROLS

24 - 

HUSQVARNA

Throttle

The lever controls engine speed.

With the lever down, the engine runs at idle and 

functions as start position.

When the engine speed increases, the centrifugal 

clutch drive automatically engages the cutting wheel.

ON

OFF

Operator Presence (OP) Grip Bar

The bar must be held against the handle for the engine 

to run. If the grip is released, the ignition system short-

circuits and the engine stops.

WARNING!
Do not over-ride the safety system 

by binding the bar to the handle. 

Control Panel On/Off Engine Switch

The ON/OFF engine switch can be used to stop the 

engine. The illustration shows the toggle switch in the 

OFF position (short circuited electrical system). 
A second switch with the same function is activated by 

the OP grip bar.
To start the engine, the control panel switch must be 

set to the ON position and the OP grip bar must be 

held in.

Содержание 966042601

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды