Husqvarna 966042601 Скачать руководство пользователя

Страница: 30 / 56

OPERATION

HUSQVARNA

-31

Before moving the machine forwards, you should

11.

ensure that the cutting wheel is above the ground

and located on either side of the stump. Move the

machine forward by releasing the brake, pushing it

forward, activating the brake again and repeating

Steps 9 and 10.
Repeat Steps 9 through 11 until the upper portion

12.

of the stump has been removed. DO NOT cut

deeper than ground level at this stage.

Set the throttle to SLOW/(START) DISENGAGE

13.

and wait until the cutting wheel stops rotating.
Release the brake and pull the machine away from

14.

the stump.
It may be necessary to clear wood chips from the

15.

area around the stump.
If you want to grind below the ground level, it may

16.

become necessary to adjust the handle position to

achieve a better hand and arm work position. Pull

the handle control lever and adjust the handle to

the desired position.
Repeat Steps 6 through 10 until you reach the

17.

desired depth.
Shut off the machine when you are done.

18.

Operating On Hills

Be very careful when operating the stump grinder

on hills because the machine can slip or move

unexpectedly.
NEVER use the machine on grades of 10° or steeper.

Transport

The Husqvarna stump grinder can be transported in a

truck, trailer, van or a large SUV (Sport Utility Vehicle).

The stump grinder is equipped with four lifting handles

(two on each side) so that two people can lift the

machine if necessary.
DO NOT attempt to lift the machine alone. Use safe

lifting techniques and DO NOT exceed your physical

limitations.
Secure the machine with tensioning belts, chains or

other approved materials.

OFF

The lifting handles can also be used to secure the machine

for transport.

Содержание 966042601

























































Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды

Husqvarna 966042601, Руководство оператора

Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды