Husqvarna 966042601 Скачать руководство пользователя

Страница: 5 / 56

SYMBOLS AND DECALS

6 -

HUSQVARNA

OFF

Decal 3
Important information

Read and make sure you understand the Operator’s

Manual before use or maintenance.
To obtain a replacement manual, contact your dealer.
Observe all safety instructions; otherwise you may

injure yourself or others.
Make sure the machine is in serviceable condition

prior to use.
Stop the engine and wait until all machine movement

comes to a standstill before service, adjustment or

cleaning.
Do not run the engine in poorly ventilated spaces.
Make sure nobody is in the vicinity of the machine

before starting and during use.
Avoid slopes that are too steep to use the machine

safely.
Clear any debris prior to use.

Decal 4

Wear goggles or safety glasses and ear protection

when using the unit.

Decal 5
Warning

Engine exhaust, some of its constituents and certain

vehicle components contain or emit chemicals

considered by the State of California to cause

cancer, birth defects or other reproductive harm. The

engine emits carbon monoxide, which is a colorless,

poisonous gas.

DO NOT

use the machine in enclosed

spaces.

Decal 6

There is DANGER to your feet from the cutting blades.

Decal 9

Rabbit = Fast engage clutch.
Turtle = Slow disengage clutch.

Decal 10

Handle adjustment.

Decal 11

No step.

Decal 12

O = off, I = on

Содержание 966042601

























































Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды

Husqvarna 966042601, Руководство оператора

Результаты поиска

Содержание 966042601

Отзывы:

Похожие инструкции для 966042601

Бренды по названию

Популярные бренды