Husqvarna 966042601 Скачать руководство пользователя | Manualshive

Страница: 36 / 56

background image

MAINTENANCE

HUSQVARNA

-37

WARNING!
Risk for carbon monoxide poisoning.

Perform the adjustment outdoors.

8011-128

Unscrew the sludge reservoir (1). Make sure not to

2.

misplace the o-ring (2).
Clean the reservoir and the o-ring using a cleaning

3.

solvent and dry carefully.
Put the o-ring in place in its track and replace the

4.

sludge reservoir. Tighten it moderately to avoid

damaging the threads.
Turn the fuel valve to ON and check for leaks. If it

5.

leaks, replace the o-ring.

Idle Adjustment

Start the engine and run it until it reaches normal

1.

working temperature.
Adjust the throttle to idle position or so that the

2.

engine runs at the lowest possible speed.
Turn the idle screw so that the engine idles at

3.

1250-1550 RPM.
Increase the idle speed with the throttle and move

4.

it right back to idle position. Check engine speed

again.

8011-128

1

2

«
...
34
35
36
37
38
...
»

Содержание 966042601

























































Отзывы:

Нет отзывов

Похожие инструкции для 966042601

Бренд: Yoer Страницы: 20

Бренд: TZS First AUSTRIA Страницы: 18

Бренд: VONROC Страницы: 104

Бренд: Orphan espresso Страницы: 3

Бренд: REBER Страницы: 15

Бренд: Bosch Страницы: 24

GWS Professional 30-180 B

Бренд: Bosch Страницы: 313

Бренд: Bosch Страницы: 26

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 483

Бренд: Bosch Страницы: 25

Бренд: Bosch Страницы: 44

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 64

GWS 20-180 Professional

Бренд: Bosch Страницы: 13

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 72

PROFACTOR GWX18V-13C

Бренд: Bosch Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды