Husqvarna 1151438-95 Скачать руководство пользователя | Manualshive

Страница: 21 / 44

background image

STARTING AND STOPPING

English

–

21

Starting and stopping

Cold engine

Starting: The chain brake should be activated when starting
the chain saw. Activate the chain brake by pushing the front
hand guard forwards.

Ignition; choke: Set the choke control in the choke position.
This should automatically set the stop switch to the start
position.

Start throttle: The correct choke/start throttle setting is
obtained by moving the control to the choke position.

If the machine is fitted with an air purge (A): Press the air
purge repeatedly until fuel begins to fill the bulb. The bulb
need not be completely filled.

If the machine is fitted with a decompression valve (B): Press
the valve to reduce the pressure in the cylinder and make
starting easier. You should always use the decompression
valve when starting the machine. Once the machine has

started the valve will automatically return to its original
setting.

Warm engine

Use the same procedure as for starting a cold engine but
without setting the choke control in the choke position. The
correct choke/start throttle setting is obtained by moving the
choke control to the choke position and then pushing it in
again.

Starting

Grip the front handle with your left hand. Hold the chain saw
on the ground by placing your right foot through the rear
handle. Pull the starter handle with your right hand and pull
out the starter cord slowly until you feel a resistance (as the
starter pawls engage) then pull firmly and rapidly. Never
wrap the starter cord around your hand

CAUTION! Do not pull the starter cord all the way out and do
not let go of the starter handle when the cord is fully
extended. This can damage the machine.

Push in the choke control as soon as the engine fires and
make repeated starting attempts. Immediately press and
release the throttle when the engine starts. That will
disengage the throttle latch.

As the chain brake is still activated the engine must return to
idling speed as soon as possible by disengaging the throttle

!

WARNING! Note the following before
starting:

The chain brake must be engaged when the
chain saw is started to reduce the chance
of contact with the moving chain during
starting.

Never start a chain saw unless the bar,
chain and all covers are fitted correctly.
Otherwise the clutch can come loose and
cause personal injuries.

Place the machine on firm ground. Make
sure you have a secure footing and that the
chain cannot touch anything.

Keep people and animals well away from
the working area.

B

A

«
...
19
20
21
22
23
...
»

Содержание 1151438-95













































Отзывы:

Нет отзывов

Похожие инструкции для 1151438-95

Бренд: CAMPAGNOLA Страницы: 122

Бренд: Gardeo Страницы: 46

Бренд: Eckman Страницы: 16

Бренд: Echo Страницы: 156

Бренд: Gardena Страницы: 20

Бренд: STERWINS Страницы: 48

Бренд: BCP Страницы: 4

Бренд: Gama Garden Страницы: 17

Бренд: GARDENJACK Страницы: 25

Бренд: Makita Страницы: 34

Бренд: Husqvarna Страницы: 9

Бренд: Husqvarna Страницы: 8

Бренд: Husqvarna Страницы: 8

Бренд: Echo Страницы: 38

Бренд: Stark Страницы: 14

Бренд: Ryobi Страницы: 4

Бренд: Ryobi Страницы: 28

Бренд: Poulan Pro Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды