Husqvarna 1151438-95 Скачать руководство пользователя | Manualshive

Страница: 32 / 44

background image

MAINTENANCE

32 – English

High speed jet H

At the factory the engine is adjusted at sea level. When
working at a high altitude or in different weather
conditions, temperatures and atmospheric humidity, it
may be necessary to make minor adjustments to the
high speed jet.

CAUTION! If the high speed jet is screwed in too far, it
may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that
the engine satisfies the applicable legal requirements at the
same time as achieving maximum performance. The
carburetor’s high speed jet is then locked using a limiter cap
in the fully screwed out position. The limiter cap limits the
potential to adjust the high speed jet to at most half a turn.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine
accelerates without hesitation and the machine 4-cycles a
little at max. speed. It is also important that the chain does
not rotate at idle. If the L-jet is set too lean it may cause
starting difficulties and poor acceleration. If the H-jet is set
too lean the machine will have less power, poor acceleration
and could suffer damage to the engine.

Checking, maintaining and
servicing chain saw safety
equipment

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake
and clutch drum. Dirt and wear can impair operation of the
brake.

Regularly check that the brake band is at least 0.024 inch
(0.6 mm) thick at its thinnest point.

Checking the front hand guard

Make sure the front hand guard is not damaged and that
there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure
it moves freely and that it is securely anchored to the clutch
cover.

Checking the inertia brake release

With the engine turned off, hold the chain saw over a stump
or other firm object. Let go of the front handle so that the bar
drops towards the stump as the chain saw rotates around the
rear handle.

When the bar hits the stump the brake should be
applied.

Note! All servicing and repair work on the machine requires
special training. This is especially true of the machine

′

s

safety equipment. If your machine fails any of the checks
described below we recommend you to contact our
servicing dealer.

«
...
30
31
32
33
34
...
»

Содержание 1151438-95













































Отзывы:

Нет отзывов

Похожие инструкции для 1151438-95

Бренд: Tanaka Страницы: 18

Бренд: McCulloch Страницы: 17

Бренд: bonomi Страницы: 20

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 21

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 19

Бренд: Craftsman Страницы: 47

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 49

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 50

Бренд: Craftsman Страницы: 42

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 57

Бренд: Craftsman Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды