Husqvarna 1151438-95 Скачать руководство пользователя | Manualshive

Страница: 15 / 44

background image

GENERAL SAFETY PRECAUTIONS

English

–

15

•

Adjust the tension on the chain by turning the wheel
down (+) for tighter tension and up (-) to loosen the
tension.

•

Tighten the bar clutch by turning the knob clockwise.

•

Fold the knob back in to lock the tensioning.

Lubricating cutting equipment

Chain oil

Chain oil must demonstrate good adhesion to the chain and
also maintain its flow characteristics regardless of whether it
is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal
chain oil which has a vegetable oil base. We recommend the
use of our own oil for both maximum chain life and to
minimise environmental damage. If our own chain oil is not
available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to
you and damage the machine and environment.

Filling with chain oil

•

All our chain saws have an automatic chain lubrication
system. On some models the oil flow is also adjustable.

•

The saw chain oil tank and the fuel tank are designed so
that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the
right sort of chain oil (if the oil is too thin it will run out
before the fuel), and that you adjust the carburetor as
recommended (a lean mixture may mean that the fuel
lasts longer than the oil) and that you also use the
recommended cutting equipment (a bar that is too long
will use more chain oil).

Checking chain lubrication

•

Check the chain lubrication each time you refuel. See
instructions under the heading Lubricating the bar tip
sprocket.

Aim the tip of the bar at a light coloured surface about 20
cm (8 inches) away. After 1 minute running at 3/4 throttle
you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

•

Check that the oil channel in the bar is not obstructed.
Clean if necessary.

•

Check that the groove in the edge of the bar is clean.
Clean if necessary.

!

WARNING! Poor lubrication of cutting
equipment may cause the chain to snap,
which could lead to serious, even fatal
injuries.

IMPORTANT! When using vegetable based saw chain oil,
dismantle and clean the groove in the bar and saw chain
before long-term storage. Otherwise there is a risk of the
saw chain oil oxidizing, which will result in the saw chain
becoming stiff and the bar tip sprocket jamming.

«
...
13
14
15
16
17
...
»

Содержание 1151438-95













































Отзывы:

Нет отзывов

Похожие инструкции для 1151438-95

Бренд: Zenoah Страницы: 16

Бренд: MTD Страницы: 24

Бренд: Echo Страницы: 10

Бренд: Echo Страницы: 60

Бренд: Poulan Pro Страницы: 18

Бренд: Valex Страницы: 20

Бренд: BCP Страницы: 4

Бренд: Zgonc Страницы: 56

Бренд: Oleo-Mac Страницы: 216

CS-3400 Type 1E

Бренд: Echo Страницы: 23

Бренд: Echo Страницы: 340

Бренд: Makita Страницы: 12

Бренд: Greencut Страницы: 18

Бренд: Skil Страницы: 108

Бренд: Villager Страницы: 172

Бренд: The Handy Страницы: 12

Бренд: Troy-Bilt Страницы: 24

Бренд: Troy-Bilt Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды