Husqvarna 1151438-95 Скачать руководство пользователя | Manualshive

Страница: 18 / 44

background image

ASSEMBLY

18 – English

Fit the bar over the bar bolts. Place the bar in its rearmost
position. Place the chain over the drive sprocket locate it in
the groove on the bar. Begin on the top edge of the bar.

Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.

Install the clutch cover and locate the chain tensioner pin in
the clutch cover. Check that the chain’s drive links fit
correctly over the drive sprocket and that the chain is
correctly located in the groove in the bar. Install the chain
tensioning pulley but do not tighten.

Tension the chain by turning the wheel down (+). The chain
should be tensioned until it does not sag from the underside
of the bar.

The chain is correctly tensioned when it does not sag from
the underside of the bar, but can still be turned easily by
hand. Hold up the bar tip and tighten the bar knob by turning
the knob clockwise.

When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the chain

tension regularly. A correctly tensioned chain ensures good
cutting performance and long life.

Note: If clutch cover is difficult to remove, replace bar nuts,
engage brake and rerelease (an audible click will be heard if
released properly).

«
...
16
17
18
19
20
...
»

Содержание 1151438-95













































Отзывы:

Нет отзывов

Похожие инструкции для 1151438-95

Бренд: ICS Страницы: 15

Бренд: Zenoah Страницы: 17

Бренд: Valex Страницы: 16

Бренд: ICS Страницы: 26

Бренд: GreenWorks Pro Страницы: 41

Бренд: EarthQuake Страницы: 32

Бренд: CAMPAGNOLA Страницы: 168

Бренд: Ikra Страницы: 30

EKSN 2200-40 WK

Бренд: IKRA Mogatec Страницы: 180

Бренд: Cub Cadet Страницы: 24

Бренд: Maruyama Страницы: 44

Бренд: Grizzly Tools Страницы: 160

Бренд: EarthWise Страницы: 40

Бренд: Kasei Страницы: 46

Бренд: TCK Страницы: 20

CS-400 - PARTS CATALOG SERIAL NUMBER C09212001001 -...

Бренд: Echo Страницы: 34

Бренд: Echo Страницы: 88

Бренд: Husqvarna Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды