Husqvarna 1151438-95 Скачать руководство пользователя | Manualshive

Страница: 12 / 44

background image

GENERAL SAFETY PRECAUTIONS

12 – English

Cutting equipment designed to reduce
kickback

The only way to avoid kickback is to make sure that the
kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction
and keeping the chain sharp and well-maintained you can
reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available
in standard and low-kickback versions.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you
should replace a worn or damaged bar or chain with a bar
and chain combinations recommended by Husqvarna. See
instructions under the heading Technical Data for a list of
replacement bar and chain combinations we recommend.

Bar

•

Length (inches/cm)

•

Number of teeth on bar tip sprocket (T).

•

Chain pitch (inches). The spacing between the drive links
of the chain must match the spacing of the teeth on the
bar tip sprocket and drive sprocket.

•

Number of drive links. The number of drive links is
determined by the length of the bar, the chain pitch and
the number of teeth on the bar tip sprocket.

•

Bar groove width (inches/mm). The groove in the bar
must match the width of the chain drive links.

•

Chain oil hole and hole for chain tensioner. The bar must
be matched to the chain saw design.

Chain

•

Chain pitch (inches)

•

Drive link width (mm/inches)

•

Number of drive links.

Sharpening your chain and adjusting depth
gauge setting

General information on sharpening cutting teeth

•

Never use a blunt chain. When the chain is blunt you
have to exert more pressure to force the bar through the
wood and the chips will be very small. If the chain is very
blunt it will produce wood powder and no chips or
shavings.

•

A sharp chain eats its way through the wood and
produces long, thick chips or shavings.

!

WARNING! Faulty cutting equipment or the
wrong combination of bar and saw chain
increases the risk of kickback! Only use the
bar/saw chain combinations we
recommend, and follow the filing
instructions. See instructions under the
heading Technical data.

IMPORTANT! No saw chain design eliminates the danger
of kickback.

!

WARNING! Any contact with a rotating saw
chain can cause extremely serious injuries.

«
...
10
11
12
13
14
...
»

Содержание 1151438-95













































Отзывы:

Нет отзывов

Похожие инструкции для 1151438-95

Бренд: Zenoah Страницы: 15

Бренд: McCulloch Страницы: 2

Бренд: Narex Страницы: 64

Бренд: Worx Страницы: 228

Бренд: Jonsered Страницы: 80

Бренд: Jonsered Страницы: 136

Бренд: Poulan Pro Страницы: 20

Бренд: YATO Страницы: 116

YELLOW GARDENLINE YGL N.G. 5351

Бренд: Zgonc Страницы: 48

Бренд: HART Страницы: 88

Бренд: Bosch Страницы: 153

Бренд: Bosch Страницы: 328

Бренд: Bosch Страницы: 419

Бренд: Gardenline Страницы: 53

Бренд: Dolmar Страницы: 44

Бренд: Topsun Страницы: 36

Бренд: Royal Страницы: 132

Бренд: Elem Garden Technic Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды