background image

cleaning  the  heat  exchanger  or  the  bur-
ners,  chemical  products  or  steel  bru-
shes MUST NOT BE USED.
Make  sure  that  the  tops  of  the  burners
with  the  holes  are  free  from  encrusta-
tions.

– Reassemble  the  items  removed  from

the boiler, making sure to follow the cor-
rect sequence.

– Check operation of the main burner.
– After  assembly  of  all  the  gas  connec-

tions,  these  must  be  tested  for  sound-
ness,  using  soapy  water  or  appropriate
products. DO NOT USE NAKED FLAMES.

– Do not use calcium chloride to treat the

plastic  component  during  generator
maintenance. 

6.4.4.1

Chimney sweep function 

To  check  boiler  combustion,  press  at  the
same time the installer's key (

) for

a few seconds. 
The  chimney  sweep  function  will  switch  on
and will continue for 15 minutes. 
During the 15 minutes functioning of chim-
ney  sweep  function,  pressing  the  keys  (
and 

) take the boiler respective at maxi-

mum (Hi) and at minimum (Lo) power. 
From  that  moment,  the  boiler  will  start
working  in  heating  mode  at  maximum
power,  with  cut  off  at  80°C  and  re-ignition
at 70°C.

Before activating the chimney sweep func-
tion make sure that the radiator valves or
eventual zone valves are open

.

For  exit  to  the  chimney  sweep  function
press the key 

of the control panel.

The chimney sweep function will automa-
tically  switch  off  after  15  minutes  from

the activation.

6.4.5

ERROR MESSAGES

When  there  is  a  ERROR  message,  an
alarm  appears  on  the  display 

and  switch

on t he red led. 

Descriptions  of  the  ERRORS  with  relative
alarms and solutions are given below:

FUMES  DISCHARGE  ERROR

ALARM 01 

(fig. 22)

The fumes thermostat has intervened. If
the condition causing the problem persi-
sts for two minutes, the boiler stops for
an enforced period of thirty minutes. 
At  the  end  of  this  period,  the  boiler  re-
attempts ignition. 

LOW  WATER  PRESSURE  ERROR
ALARM 02 

(fig. 22/a)

If  the  pressure  detected  by  the  water
pressure valve is lower than 0.5 bar, the
boiler  stops  and  the  display  shows  the
alarm “AL 02”. 
Bring  the  pressure  back  to  normal  by
means  by  acting  on  the  telescopic  loa-
ding knob.
Lower the knob and turn it anti-clockwise
to  open  until  the  pressure  indicated  on
the pressure gauge reaches 1 - 1.2 bar.
WHEN FILLING HAS BEEN COMPLETED,
CLOSE  THE  KNOB  BY  TURNING  IT
CLOCKWISE.

If the load procedure has to be repea-
ted  several  times,  it  is  advisable  to
check  that  the  seal of  the  heating  cir-
cuit  is  intact  (check  that  there  are  no

l

eaks).

D.H.W. SENSOR ERROR ALARM 04 

The  D.H.W.  probe  is  not  operational  in
these boiler models; if the display shows
the AL 04 anomaly, check PAR 2.

HEATING  SENSOR ANOMALY ALARM  05

If  one  or  both  sensing  elements  of  hea-
ting  sensor  (SM1/SM2)  are  open  or
short  circuited,  the  boiler  will  not  func-
tion  and  the  display  will  show  the  alarm
“AL 05”.

FLAME BLOCK ALARM 06 

(fig. 22/b)

If the flame control has not detected the 
presence  of  the  flame  after  a  complete
ignition  sequence,  or  for  any  other  rea-
son the card cannot “see” the flame, the
boiler  will  stop  and  the  display  will  show
the alarm “AL 06”. 
Press the key

of the controls to start

up the boiler again.

SA F E T Y  T H E R M O S TAT  E R R O R
ALARM 07 

(fig. 22/c)

If  the  C.H.  sensor  (SM1/SM2)  exceeds
the 100°C the boiler does not ignite the
burner,  the  display  show AL  07  and
remains ignited the green led. If this con-
dition  restored  more  one  minute,  the
boiler  will  stop,  the  display  show  always
the  anomaly AL  07  and  switch  on  the
red led.  
Press the key

of the controls to start

up the boiler again.

PARASITE  FLAME  ERROR ALARM  08

If  the  flame  control  section  recognises
the  presence  of  flames  also  in  phases
when  they  should  not  be  present,  it

Fig. 22

Fig. 22/a

Apre

0

4

1

3

2

bar

OPEN

Fig. 22/b

Fig. 22/c

Page 30 of 34

These SENSORS must not be 
disabled or bypassed at any time.

In the case of repeated shutdown 
of this appliance, take 
appropriated action to find the 
cause and remedy the problem. 

Содержание sime 30e



































Отзывы: