manualshive.com logo in svg

Humminbird MEGA 360 Fortrex, Руководство по установке

Поделиться
Скачать
Humminbird MEGA 360 Fortrex Скачать руководство пользователя страница 8

2

Introduction

NOTE:

 MEGA 360 Imaging can be shared with all SOLIX, HELIX G3N, and HELIX G2N 

models over Ethernet. 

Transducers: 

The MEGA 360 Imaging transducer is compatible with the following 

transducers: 

• 

HW Dual Spectrum

• 

HW MEGA DI+

• 

HW MEGA DI+/MEGA SI+

•  Built-in MEGA Imaging transducer on a Minn Kota trolling motor

Cables:

 Your MEGA 360 Imaging transducer comes with the cables required to 

connect directly to your Humminbird fish finder. This includes a 10' MEGA 360 power 
cable, a 10’ SOLIX transducer cable, and a 10' HELIX transducer adapter cable. 
However, depending on your Humminbird model and system configuration, you may 
choose to purchase a transducer splitter cable (y-cable) to connect the MEGA 360 to 
another compatible transducer, as shown below. 

MEGA 360 compatible transducer 
splitter cables (y-cables)

MEGA 360 compatible transducers

MEGA 360 7-pin Transducer Y-cable:

 

9 M360 2DDI Y (720107-1)

HELIX Dual Spectrum (Type 9 / 7-pin)
HELIX MDI+ (Type 9 / 7-pin)
HELIX MDI+/MSI+ (Type 9 / 7-pin)

MEGA 360 14-pin Transducer Y-cable: 

14 M360 2DDI Y (720108-1)

SOLIX Dual Spectrum
SOLIX MDI+ 
SOLIX MDI+/MSI+
Built-in MEGA Imaging*

* If this cable is being used with a HELIX G3N with MEGA Side or Down  and a 

Built-in MEGA imaging transducer, then the 720109-1 AD HELIX M360 adapter (included 
with the MEGA 360) must be attached between this y-cable and the HELIX unit.

 

NOTE:

 If a MEGA SI+ transducer is connected with one of these y-cables, the 

Humminbird unit  will not be able to get SI data from the MEGA SI+ transducer – only HW 
and MEGA DI+ will be available. However, the user can get MEGA SI data from the MEGA 
360 transducer.

Содержание MEGA 360 Fortrex



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды