manualshive.com logo in svg

Humminbird MEGA 360 Fortrex, Руководство по установке

Поделиться
Скачать
Humminbird MEGA 360 Fortrex Скачать руководство пользователя страница 37

31

Control Head Setup

Selecting the Connected Transducer (HELIX)      

3. Test MEGA 360 Imaging on the Control Head

It is important to confirm that the MEGA 360 Imaging transducer is providing sonar 
returns to the display. The instructions in this section should be performed at trolling 
speeds in calm, open water, in a large area that is far from shallow water, boats, or 
other obstacles.

WARNING! 

The pod should NOT be in the water during high speed travel. The pod 

should only be deployed when the boat is traveling at trolling speeds.

SOLIX Series

1. 

Tap the View widget icon in the side bar.

NOTE: 

Once the MEGA 360 has been detected the first time, the 360 Imaging 

view will display on the Favorite Views widget.

2. 

Tap 360 Imaging. 

3.  The sonar returns from the MEGA 360 scan will begin to display on the 

MEGA 360 View. Review the display for the following information and see the 
illustration 

Reviewing the 360 View

.

• 

Bottom:

 Confirm that the bottom is visible on-screen.

• 

Blocked Beams:

 If the beams hit a hard surface, it will appear as bright 

white on the display. If the beams are blocked by any objects, move the 
objects if possible. You can also adjust the 360 Range on the X-Press Menu 
to see more or less detail on the display. In some cases, the trolling motor 
will appear on the display as a shadow.

Содержание MEGA 360 Fortrex



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды