manualshive.com logo in svg

Humminbird MEGA 360 Fortrex, Руководство по установке

Поделиться
Скачать
Humminbird MEGA 360 Fortrex Скачать руководство пользователя страница 45

39

Troubleshooting

Fishing System Defaults to Simulator with a Transducer Attached

In addition to the MEGA 360 Imaging accessory transducer, you will have a standard 
Humminbird transducer connected to the control head. A connected and functioning 
transducer with built-in temperature will cause the newly-started Fishing System to 
go into Normal operating mode automatically. If, when you power up the Fishing 
System, it goes into Simulator mode automatically, even though a transducer is 
already connected, this means that the control head is not detecting the transducer. 
Perform the following troubleshooting tasks:

•  Check the connections of all transducers that are connected to the control 

head or Ethernet network. See the transducer installation guide that was 
included with your Fishing System for connection information.

•  Review this MEGA 360 Imaging installation guide to confirm that the 

transducer cable is connected correctly to the Fishing System. Reconnect if 
necessary, and power on the Fishing System again to see if this fixes the 
problem.

•  Replace the non-functioning transducer with a known good transducer if 

available and power up the control head again.

•  Check the transducer cable. Replace the transducer if the cable is damaged 

or corroded.

Содержание MEGA 360 Fortrex



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды