manualshive.com logo in svg

Humminbird MEGA 360 Fortrex, Руководство по установке

Поделиться
Скачать
Humminbird MEGA 360 Fortrex Скачать руководство пользователя страница 15

9

Trolling Motor Bracket

2. Install the Trolling Motor Bracket

Proceed to the installation section of the type of trolling motor bracket you 
purchased:

A. Ultrex Trolling Motor Mount (MEGA 360 Ultrex)

OR

B. Fortrex/Maxxum Trolling Motor Mount (MEGA 360 Fortrex)

A. Ultrex Trolling Motor Mount (MEGA 360 Ultrex)

WARNING! 

Disconnect the motor from all sources of electrical power before you 

start installation.

WARNING! 

Confirm that the trolling motor is properly secured to the boat and will 

not shift during the installation.

Assemble the Bracket

1. 

The trolling motor should be in the fully retracted (flat) position on the boat 
deck for this installation.

2. 

Disconnect the motor from all sources of electrical power.

3. 

In addition to the requirements listed in the 

Prepare for Installation

 section, 

determine if the bracket will be installed on the left or right side of the 
trolling motor, so the transducer pod is mounted outboard of the trolling 
motor and on the centerline of the boat. Determine the mount position from 
the bow, facing the (forward) direction of travel.

If the trolling motor deploys starboard side (right) on the bow,

 you will 

mount the bracket on the left side of the trolling motor. Position the bracket 
so the straight edge faces to the left as shown in the illustration.

Содержание MEGA 360 Fortrex



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды