Huawei SUN2000-10KTLM1 Скачать руководство пользователя страница 98

Страница: 98 / 124

Name

Severity Cause

Solution

2063

Cabinet

overtemp

erature

Minor

Cause ID = 1
● The SUN2000 is

installed in a place with

poor ventilation.

● The ambient

temperature exceeds the

upper threshold.

● The SUN2000 is not

operating properly.

● Check the ventilation and

ambient temperature at the

SUN2000 installation

position.

● If the ventilation is poor or

the ambient temperature

exceeds the upper threshold,

improve the ventilation and

heat dissipation.

● If the ventilation and

ambient temperature are

normal, contact your dealer

or Huawei technical support.

2064

Equipme

nt fault

Major

Cause ID = 1–12
An unrecoverable fault

occurs on a circuit inside

the SUN2000.

Turn off the AC output switch

and DC input switch, and then

turn them on after 5 minutes. If

the alarm persists, contact your

dealer or Huawei technical

support.

2065

Upgrade

failed or

version

mismatch

Minor

Cause ID = 1–6
The upgrade is not

completed normally.

1. Perform an upgrade again.
2. If the upgrade fails several

times, contact your dealer or

Huawei technical support.

2068

Battery

abnormal

Minor

Cause ID = 1–4
● The battery is faulty.
● The battery is

disconnected.

● The battery switch trips

when the inverter is

operating.

1. If the fault indicator on the

battery is steady on or

blinking, contact the battery

dealer.

2. Check whether the battery

enabling, power, and

communications cable

connections are correct, and

whether the communications

parameters are consistent

with the RS485

configurations of the inverter.

3. Check whether the battery

auxiliary power switch is

turned on.

61440

Faulty

monitorin

g unit

Minor

Cause ID = 1
● The flash memory is

insufficient.

● The flash memory has

bad sectors.

Turn off the AC output switch

and DC input switch, and then

turn them on after 5 minutes. If

the alarm persists, replace the

monitoring board or contact

your dealer or Huawei technical

support.

SUN2000-(3KTL-10KTL)-M1

User Manual

8 Maintenance

Issue 02 (2020-11-20)

Содержание SUN2000-10KTLM1





























































































































Результаты поиска

Содержание SUN2000-10KTLM1

Отзывы:

Похожие инструкции для SUN2000-10KTLM1

Бренды по названию

Популярные бренды

Huawei SUN2000-10KTLM1, Руководство пользователя

Результаты поиска

Содержание SUN2000-10KTLM1

Отзывы:

Похожие инструкции для SUN2000-10KTLM1

Бренды по названию

Популярные бренды