Huawei SUN2000-10KTLM1 Скачать руководство пользователя страница 121

Страница: 121 / 124

Locating Insulation Resistance Faults

If the ground resistance of a PV string connected to a solar inverter is too low, the

solar inverter generates a Low Insulation Resistance alarm.
The possible causes are as follows:
●

A short circuit occurs between the PV array and the ground.

●

The ambient air of the PV array is damp and the insulation between the PV

array and the ground is poor.

To locate the fault, connect each PV strings to a solar inverter, power on and

check the solar inverter, and locate the fault based on the alarm information

reported by the FusionSolar app. If a system is not configured with any optimizer,

skip the corresponding operations. Perform the following steps to locate an

insulation resistance fault.

NO TICE

If two or more ground insulation faults occur in a single PV string, the following

method cannot locate the fault. You need to check the PV modules one by one.

Step 1 The AC power supply is connected, and set the DC switch at the bottom of the

solar inverter to OFF. If the solar inverter connects to batteries, wait for 1 minute,

and turn off the the battery switch and then the auxiliary power switch of the

battery.

Step 2 Connect each PV string to the solar inverter and set the DC switch to ON. If the

solar inverter status is Shutdown: Command, choose Device Commissioning >

Maintenance > Inverter ON/OFF on the app and send a startup command.

Step 3 Log in to the FusionSolar app and choose My > Device Commissioning. On the

Device Commissioning screen, connect and log in to the solar inverter, and access

the Alarm management screen. Check whether the Low Insulation Resistance

alarm is reported.
●

If the Low Insulation Resistance alarm is not reported one minute after the

DC is supplied, choose Device Commissioning > Maintenance > Inverter

ON/OFF on the app and send a shutdown command. Set the DC switch to

OFF and go to

Step 2

to connect another PV string to the solar inverter for a

check.

SUN2000-(3KTL-10KTL)-M1

User Manual

E Locating Insulation Resistance Faults

Issue 02 (2020-11-20)

114

Содержание SUN2000-10KTLM1





























































































































Результаты поиска

Содержание SUN2000-10KTLM1

Отзывы:

Похожие инструкции для SUN2000-10KTLM1

Бренды по названию

Популярные бренды

Huawei SUN2000-10KTLM1, Руководство пользователя

Результаты поиска

Содержание SUN2000-10KTLM1

Отзывы:

Похожие инструкции для SUN2000-10KTLM1

Бренды по названию

Популярные бренды