Huawei SUN2000-10KTLM1 Скачать руководство пользователя страница 123

Страница: 123 / 124

Device Commissioning > Maintenance > Inverter ON/OFF on the app

and send a shutdown command. Set the DC switch to OFF. Go to

Step 2

to check other PV strings. Then go to

Step 8

–

If the Low Insulation Resistance alarm is still reported one minute after

the DC is supplied, go to

Step 5

●

If not, go to

Step 5

Step 5 Set the DC switch to OFF, disconnect the possible faulty PV modules and

corresponding optimizers from the PV string, and connect a DC extension cable

with an MC4 connector to the adjacent PV modules or optimizers. Set the DC

switch to ON and view the alarm information.
●

If the Low Insulation Resistance alarm is not reported one minute after the

DC is supplied, the fault occurs on the disconnected PV module and optimizer.

Choose Device Commissioning > Maintenance > Inverter ON/OFF on the

app and send a shutdown command. Go to

Step 7

●

If the Low Insulation Resistance alarm is still reported one minute after the

DC is supplied, the fault does not occur on the disconnected PV module or

optimizer. Go to

Step 6

Step 6 Set the DC switch to OFF, reconnect the removed PV module and optimizer, and

repeat

Step 5

to check the adjacent PV modules and optimizers.

Step 7 Determine the position of the ground insulation fault.

1. Disconnect the possible faulty PV module from the optimizer.
2. Set the DC switch to OFF.
3. Connect the possible faulty optimizer to the PV string.
4. Set the DC switch to ON. If the solar inverter status is Shutdown: Command,

choose Device Commissioning > Maintenance > Inverter ON/OFF on the

app and send a startup command. Check whether the Low Insulation

Resistance alarm is reported.
–

If the Low Insulation Resistance alarm is not reported one minute after

the solar inverter is powered on, the PV module is faulty. Choose Device

Commissioning > Maintenance > Inverter ON/OFF on the app and send

a shutdown command.

–

If the Low Insulation Resistance alarm is still reported one minute after

the solar inverter is powered on, the optimizer is faulty.

5. Set the DC switch to OFF. Replace the faulty component to rectify the

insulation resistance fault. Go to

Step 2

to check other PV strings. Then go to

Step 8

Step 8 If the solar inverter connects to batteries, turn on the auxiliary power switch of the

battery and then the battery switch. Set the DC switch to ON. If the solar inverter

status is Shutdown: Command, choose Device Commissioning > Maintenance >

Inverter ON/OFF on the app and send a startup command.

----End

SUN2000-(3KTL-10KTL)-M1

User Manual

E Locating Insulation Resistance Faults

Issue 02 (2020-11-20)

116

Содержание SUN2000-10KTLM1





























































































































Результаты поиска

Содержание SUN2000-10KTLM1

Отзывы:

Похожие инструкции для SUN2000-10KTLM1

Бренды по названию

Популярные бренды

Huawei SUN2000-10KTLM1, Руководство пользователя

Результаты поиска

Содержание SUN2000-10KTLM1

Отзывы:

Похожие инструкции для SUN2000-10KTLM1

Бренды по названию

Популярные бренды