Huawei RRU Скачать руководство пользователя страница 28

Страница: 28 / 100

Figure 1-2

Lifting a weight

Safety Guide on Ladder Use

Checking the Ladder

Check the ladder before using it. Check the maximum weight that the ladder can support.

Never overload the ladder.

Placing the Ladder

The slant angle is preferred to be 75

. The slant can be measured with the angle square or

with arms, as shown in

Figure 1-3

. When using a ladder, place the wider end of the ladder

on the ground and take protective measures on the base of the ladder against slippage. Place
the ladder on a stable ground.

When climbing the ladder, ensure the following:

The gravity of the body does not shift from the edge of the ladder.

Keep balance on the ladder before performing any operation.

Do not climb higher than the fourth highest step of the ladder.

If you tend to climb to the roof, the length of the ladder should be at least one meter higher than
the eave, as shown in

Figure 1-4

1 Safety Information

RRU

User Guide

1-10

Huawei Proprietary and Confidential

Issue 01 (2008-04-18)

Содержание RRU





































































































Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды

Huawei RRU, Руководство пользователя

Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды