Huawei RRU Скачать руководство пользователя страница 85

Страница: 85 / 100

3.4 Installing the RRU on the Ground or Rooftop

If...

Then...

Only one RRU needs to be installed,

Go to

3.4.1 Installing a Single RRU

Two RRUs need to be installed,

Go to

3.4.2 Install Two RRUs

Three RRUs need to be installed,

Go to

3.4.3 Install Three RRUs

3.5 Installing the RRU on the Tower

Step 3

Check whether the SRXU needs to be installed. Perform the next step accordingly.

If...

Then...

The SRXU needs to be installed,

Go to

Step 4

The SRXU does not need to be installed,

Go to

Step 5

Step 4

Install the SRXU. For details, refer to

3.6 Installing the SRXU

Step 5

Install RRU and SRXU cables. For details, refer to

3.7 Installing RRU and SRXU Cables

Step 6

Check RRU and SRXU hardware installation. For details, refer to

Checking RRU and SRXU

Hardware Installation

Step 7

Install the housing of the RRU and SRXU. For details, refer to

3.9 Installing the Housing of

the RRU and SRXU

----End

3.3 Preparing for the NodeB Installation

This describes how to prepare for the NodeB installation. Before installing the NodeB, you need
to unpack the NodeB and prepare necessary tools.

3.3.1 Unpacking Inspection for the NodeB

This describes how to unpack the NodeB and check the integrity of the equipment. This is a
prerequisite for the successful installation.

3.3.2 Tools and Instruments for NodeB Installation

This describes the general tools, special tools, and instruments required for the NodeB
installation.

3.3.1 Unpacking Inspection for the NodeB

This describes how to unpack the NodeB and check the integrity of the equipment. This is a
prerequisite for the successful installation.

RRU
User Guide

3 Installing RRU and SRXU Hardware

Issue 01 (2008-04-18)

Huawei Proprietary and Confidential

3-27

Содержание RRU





































































































Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды

Huawei RRU, Руководство пользователя

Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды