Huawei RRU Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 100

background image

l

During the drilling, wear the protective gloves.

l

Prevent the metal shavings from getting into the cabinet. After drilling, clean the metal
shavings in time.

Handling Sharp Objects

CAUTION

When carrying the device by hand, wear the protective gloves to prevent injury by sharp objects.

Handling Fans

l

When replacing a component, place the component, screw, and tool at a safe place to prevent
them from falling into the running fan.

l

When replacing the ambient equipment around the fan, do not place the finger or board
into the running fan until the fan is switched off and stops running.

Moving Heavy Objects

Wear the protective gloves when moving heavy objects.

CAUTION

l

Be careful when moving heavy objects.

l

When moving the chassis outwards, be aware about the unfixed or heavy objects on the
chassis to prevent injury.

l

Two persons should be available to move a chassis; one person must not move a heavy
chassis. When moving a chassis, keep your back straight and move stably to prevent a
sprain.

l

When moving or lifting a chassis, hold the handle or bottom of the chassis. Do not hold the
handle of the installed modules in the chassis, such as the power module, fan module, or
board.

1.8 Others

Inserting and Removing a Board

CAUTION

When inserting a board, wear the ESD wrist strap or gloves. Insert the board gently to prevent
any bent pins on the backplane.

1 Safety Information

RRU

User Guide

1-12

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd

Issue 01 (2008-04-18)

«
...
28
29
30
31
32
...
»

Содержание RRU





































































































Отзывы:

Нет отзывов

Похожие инструкции для RRU

Бренд: D-Link Страницы: 2

Бренд: Panasonic Страницы: 132

EASA-PHONE KX-T30810

Бренд: Panasonic Страницы: 16

Бренд: KBS Страницы: 37

Бренд: Abus Страницы: 2

Бренд: Banner Страницы: 12

One Step BRZ0070

Бренд: Baby Brezza Страницы: 4

Бренд: Babboe Страницы: 7

Бренд: Babboe Страницы: 7

Бренд: La Crosse Technology Страницы: 2

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

Бренд: Vega Страницы: 2

Бренд: Vega Страницы: 11

WorkCentre Pro 123

Бренд: Xerox Страницы: 4

CommCenter D1 Series

Бренд: Federal Signal Corporation Страницы: 16

Бренд: Empire Comfort Systems Страницы: 4

Бренд: DAVIS Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды