Huawei RRU Скачать руководство пользователя страница 58

Страница: 58 / 100

Typical
Networking
Mode

Antenna Type and
Quantity of RRUs

Cable Connection

2 x 2 in no TX
diversity mode

ANT_TX/RXA ports and ANT_RXB
ports on RRU 0 and RRU 1.

1 x 1 in TX diversity
mode

Two RRUs

One dual polarization
antenna

Two feeder jumpers and one
interconnect jumper

The DIN connectors of the two feeder
jumpers are linked to the ANT_TX/
RXA ports on RRU 0 and RRU 1.

The interconnect jumper is connected
to the RX_IN/OUT ports on RRU 0 and
RRU 1 that are combined.

1 x 2 in TX diversity
mode

3 x 1 in no TX
diversity mode

Three RRUs

Three dual polarization
antennas

Six antenna jumpers

The DIN connectors of the six antenna
jumpers are linked to the ANT_TX/
RXA ports and ANT_RXB ports on
RRU 0, RRU 1, and RRU 2.

3 x 2 in no TX
diversity mode

4-way RX diversity

One RRU

One SRXU

Two antenna jumpers and one DC
power cable

The DIN connectors of the two antenna
jumpers are linked to the ANT_RXC
and ANT_RXD ports at the bottom of
the SRXU.

One end of the DC power cable is
connected to the RET/PWR_SRXU
port at the bottom of the RRU, and the
other end is connected to the
PWR_SRXU socket at the bottom of
the SRXU.

2 RRU and SRXU Hardware

RRU

User Guide

2-26

Huawei Proprietary and Confidential

Issue 01 (2008-04-18)

Содержание RRU





































































































Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды

Huawei RRU, Руководство пользователя

Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды