Huawei RRU Скачать руководство пользователя страница 66

Страница: 66 / 100

Figure 3-7

Recommended space requirements of one RRU with and without the SRXU (unit:

mm)

The recommended space around the equipment is as follows:

At least 500 mm under the equipment for cabling. It is recommended that the space is 1,200
mm between the bottom and the ground for easy maintenance.

At least 800 mm in front of the equipment for maintenance.

At least 200 mm above the equipment for maintenance.

At least 600 mm on the left of the equipment for maintenance.

At least 300 mm on the right of the equipment for maintenance.

Regardless of whether the SRXU is fixed to the RRU, the space requirements are the same.

Figure 3-8

shows the minimal space requirements of one RRU with and without the SRXU.

3 Installing RRU and SRXU Hardware

RRU

User Guide

3-8

Huawei Proprietary and Confidential

Issue 01 (2008-04-18)

Содержание RRU





































































































Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды

Huawei RRU, Руководство пользователя

Результаты поиска

Содержание RRU

Отзывы:

Похожие инструкции для RRU

Бренды по названию

Популярные бренды