Huawei Quidway S3900 Series Скачать руководство пользователя страница 1

Страница: 1 / 95

Chapter 1 Product Overview

1-1

...........................................................................

1.1 Introduction

1-1

.............................................................................................

1.2 S3924-SI Ethernet Switch

1-2

......................................................................

1.2.1 Front Panel

1-2

....................................................................................

1.2.2 Rear Panel

1-4

.....................................................................................

1.3 S3928P-SI Ethernet Switch

1-5

....................................................................

1.3.1 Front Panel

1-5

....................................................................................

1.3.2 Rear Panel

1-9

.....................................................................................

1.4 S3928TP-SI Ethernet Switch

1-9

..................................................................

1.4.1 Front Panel

1-9

....................................................................................

1.4.2 Rear Panel

1-14

.....................................................................................

1.5 S3952P-SI Ethernet Switch

1-14

....................................................................

1.5.1 Front Panel

1-14

....................................................................................

1.5.2 Rear Panel

1-16

.....................................................................................

1.6 S3928P-EI Ethernet Switch

1-16

....................................................................

1.6.1 Front Panel

1-16

....................................................................................

1.6.2 Rear Panel

1-20

.....................................................................................

1.7 S3928F-EI Ethernet Switch

1-20

....................................................................

1.7.1 Front Panel

1-20

....................................................................................

1.7.2 Rear Panel

1-26

.....................................................................................

1.8 S3928P-PWR-EI Ethernet Switch

1-27

..........................................................

1.8.1 Front Panel

1-27

....................................................................................

1.8.2 Rear Panel

1-33

.....................................................................................

1.9 S3952P-EI Ethernet Switch

1-33

....................................................................

1.9.1 Front Panel

1-33

....................................................................................

1.9.2 Rear Panel

1-35

.....................................................................................

1.10 S3952P-PWR-EI Ethernet Switch

1-35

........................................................

1.10.1 Front Panel

1-35

..................................................................................

1.10.2 Rear Panel

1-37

...................................................................................

1.11 System Features of the S3900 Series

1-37

..................................................

Chapter 2 Preparing for Installation

2-1

...............................................................

2.1 Safety Precautions

2-1

.................................................................................

2.2 Installation Site

2-1

.......................................................................................

2.2.1 Temperature/Humidity

2-1

...................................................................

2.2.2 Cleanness

2-2

......................................................................................

2.2.3 Electromagnetic Susceptibility

2-2

.......................................................

2.2.4 Laser Safety

2-3

...................................................................................

2.3 Installation Tools

2-3

....................................................................................

Chapter 3 Installing the Switch

3-1

......................................................................

Содержание Quidway S3900 Series
































































































Результаты поиска

Содержание Quidway S3900 Series

Отзывы:

Похожие инструкции для Quidway S3900 Series

Бренды по названию

Популярные бренды

Huawei Quidway S3900 Series, Руководство по установке

Результаты поиска

Содержание Quidway S3900 Series

Отзывы:

Похожие инструкции для Quidway S3900 Series

Бренды по названию

Популярные бренды